Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Conductix-Wampfler VersaReel
Summary of Contents for Conductix-Wampfler VersaReel
- Page 1 VersaReel™ Manual XA-578590.1-US VersaReel Manual...
- Page 2 Buyer’s name - provided that Seller shall have the right to elect to defend any such suit or action for the account of Buyer. The foregoing shall be the exclusive remedies of the Buyer and all persons and entitles claiming through the Buyer. VersaReel Manual XA-578590.1-US...
- Page 3 As the world’s largest single source manufacturer of mobile electrification products, Conductix-Wamplfer has the unique ability to offer a degree of service not found anywhere else. Conductix-Wampfler's team of highly qualified service technicians and engineers have years of experience servicing our complete line of products.
-
Page 4: Table Of Contents
SECTION 4 - OPERATION Overview SECTION 5- REPLACING PARTS Quick Mount Base Guide Arm Ball Stop Spring Motor Cable and Tri-Tap Ground Fault Interrupter (GFCI) Cable End Accessory Pivot Base SECTION 6 - TROUBLESHOOTING SECTION 7 - REPLACEMENT PARTS VersaReel Manual XA-578590.1-US... -
Page 5: Section 1 - Safety
• The HAZARD SYMBOL used with the word WARNING describes unsafe actions or situations that have the potential to cause severe injury, death, and/or major equipment or property damage. NOTE • The word NOTE is used to alert you to installation, operation, programming, or maintenance information that is important, but not hazard related. VersaReel Manual XA-578590.1-US... -
Page 6: Electrical Warnings
Labels and Marking Every cable reel is marked with a label which includes the Conductix-Wampfler name and logo, the product catalog number, the individual product serial number, NEMA rating, amps, volts, watts, and cable footage. -
Page 7: Section 2 - Overview
SECTION 2 - OVERVIEW 1. Spring Motor 6. Feeder Cord 2. Spool 7. Feeder Cord Cover 3. Base 8. Ball Stop 4. Frame 9. GFCI 5. Guide Arm 10. End Accessory VersaReel Manual XA-578590.1-US... -
Page 8: Section 3 - Installation
PRIMARY UNITS ARE IN INCH POUND SECONDS authorized manufacture or installation of Conductix, Inc. products, and on the condition 10102 F Street VersaReel Manual XA-578590.1-US that it will be treated as confidential and will not be disclosed, published or reproduced in... -
Page 9: Guide Arm Position Adjustment
3. Position the guide arm in the desired orientation and re-install the two phillips screws. Position 1 shows the correct position for a wall mount, and Position 2 is the correct position for a ceiling mount. 4. Torque the screws to 18 in-lbs. Figure 9-1 Guide Arm Positions VersaReel Manual XA-578590.1-US... -
Page 10: Section 4 - Operation
Keep the reel and cable clean to avoid excessive wear and damage. Discontinue use and arrange for maintenance service if damage is found on the cable or reel. Cable should be fully retracted when not in service to maximize spring life. VersaReel Manual XA-578590.1-US... -
Page 11: Section 5- Replacing Parts
(Figure 11-3) 4. While supporting the reel's weight, align the frame holes with the base holes and insert the 1/4" hardware on both sides and tighten to 6 ft-lbs. (Figure 11-4) Figure 11-2 Figure 11-3 Figure 11-4 VersaReel Manual XA-578590.1-US... -
Page 12: Guide Arm
4. Re-attach arm to reel using the same screws and tighten down. Torque to 50 inch lbs. See Figure 12-1. 5. Re-attach ball stop, cable accessory and GFCI if needed. See cable end accessory and GFCI replacement instructions. Figure 12-1 Figure 12-2 VersaReel Manual XA-578590.1-US... -
Page 13: Ball Stop
A. Remove screws completely to replace ball stop. B. Loosen and move ball stop along cable to adjust hanging length. NOTE • Donut-style ball clamp used on reels using 12/3 cable, clamp style used on reels with 16/3 cable. Figure 13-1 Figure 13-2 VersaReel Manual XA-578590.1-US... -
Page 14: Spring Motor
See Figure 14-5 Figure 14-2 8. Once pre-turns are placed tensioning the reel, lock the reel out on ratchet to prevent retraction. 9. Re-attach guide arm. Torque screws to 50 inch lbs. Figure 11-4 Figure 11-3 Figure 14-5 VersaReel Manual XA-578590.1-US... -
Page 15: Cable And Tri-Tap
3. Remove cable wires from quick connector. See Figure 15-1. 4. Install new cable or cable with tri-tap through slot in drum. See Figure 15-2. • For Tri-Tap without GFCI, install cable through guide arm before wiring. Figure 15-1 Figure 15-2 VersaReel Manual XA-578590.1-US... - Page 16 8. Re-attach spring motor. See Page 11 Spring Motor Replacement. 9. Attach ball stop in proper location. Figure 16-1 10. Attach GFCI if applicable. See GFCI installation instructions 11. Attach desired end accessory. See cable end accessory instructions Figure 13-2 Figure 13-3 Figure 13-4 VersaReel Manual XA-578590.1-US...
-
Page 17: Ground Fault Interrupter (Gfci)
A. If required, strip cable jacket and wires to correct length. B. Attach black, white and green wire to correct accessory connection. C. Correctly install any strain relief plates or nuts included with accessory. Figure 17-3 VersaReel Manual XA-578590.1-US... -
Page 18: Pivot Base
(See Figure 18-4). 5. While supporting the reel's weight, align the frame holes with the base holes, insert 1/4" hardware and tighten to 6 ft-lbs. See Figure 18-5. Figure 18-3 Figure 18-2 Figure 18-5 Figure 18-4 VersaReel Manual XA-578590.1-US... -
Page 19: Section 6 - Troubleshooting
Dirt or contaminants on slip ring termination points • Amp or voltage above rating of reel • Clean dust from inside slip ring • Circuit arcing Excessive carbon dust accumulation • Replace brush assembly • Loss of brush to ring contact VersaReel Manual XA-578590.1-US... -
Page 20: Section 7 - Replacement Parts
GFCI Inline 12/3 XA-578852 Quad Receptable Box XA-578853 Quad Receptable Box XA-578854 Quad Receptable Box XA-51302 Single Outlet 10A, 15A XA-37464 Single Outlet XA-577871 Locking Outlet 10A, 15A XA-540975 Locking Outlet XA-573399 Spring Motor Assembly XA-573508 Quick Mount Base VersaReel Manual XA-578590.1-US... - Page 21 VersaReel Manual XA-578590.1-US...
- Page 22 Phone (+52 81) 1090 9519 (+52 81) 1090 9025 (+52 81) 1090 9013 Phone +1-402-339-9300 +1-402-339-9627 (+52 81) 1090 9014 Fax (+55 11) 4813 7330 info.us@conductix.com info.ca@conductix.com info.mx@conductix.com info.br@conductix.com latinamerica@conductix.com Contact USA for our Global Sales Offices XA-578590.1-US VersaReel Manual...
Need help?
Do you have a question about the VersaReel and is the answer not in the manual?
Questions and answers