Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epever LFP14.33KWH51.2V-P65F1
Summary of Contents for Epever LFP14.33KWH51.2V-P65F1
- Page 1 LiFePO4 (LFP) Battery Product manual LFP14.33KWH51.2V-P65F1...
-
Page 2: Table Of Contents
Contents 1 Important Safety Instructions ............1 2 General Information ................ 3 2.1 Appearance ........................3 2.2 Product size ........................5 3 Basic Information ................6 3.1 Interface definition ......................6 3.2 Product features ....................... 7 3.3 Colored touchable LCD ....................8 4 Instructions .................. -
Page 3: Important Safety Instructions
1 Important Safety Instructions ※ Thank you for choosing EPEVER Lithium Iron Phosphate (LFP) battery, please read this manual carefully before using this product. ※ It is strictly forbidden to install this product in harsh environments such as moisture, salt spray, corrosion, greasy, flammable and explosive, or a large amount of dust accumulation. - Page 4 d) It is forbidden to heat and incinerate batteries. It may melt battery components, lose safety features, or burn electrolyte. Overheating can deform, heat, smoke, or burn the battery. Emergency treatment method a) When the electrolyte leaks, avoid skin and eye contact with the electrolyte. In case of contact, wash immediately with plenty of water and seek help from a doctor.
-
Page 5: General Information
2 General Information 2.1 Appearance... - Page 6 Metal handles Pressure reducing value Circuit breaker Parallel communication interface port Grounding screw interface Parallel communication interface port Color/Touch LCD screen Inverter communication interface port Plastic Protective cover PC upper computer interface port Weak-current switch Positive connector Wall mounting bracket Negative connector Casters...
-
Page 7: Product Size
2.2 Product size... -
Page 8: Basic Information
3 Basic Information 3.1 Interface definition (1) The RS232 communication interface pin are defined as follows, and the RJ11 communication interface is used to connect the upper computer of the lithium battery PC. RJ11 Pin RJ11 Definition 1、2、6 ( RJ11) (2) The pins of the CAN/RS485 communication interface are defined as follows, and the RJ45 communication interface is used for the communication connection between the lithium battery and the inverter host. -
Page 9: Product Features
(4) The BMS communication interface pins are defined as follows, and the RJ45 communication interface is used for the parallel (host) communication connection between the lithium battery and the lithium battery. Pin No RJ45 Definition RS485-B RS485-A RS485-A (RJ45 ) RS485-B 3.2 Product features ... -
Page 10: Colored Touchable Lcd
3.3 Colored touchable LCD Interface introduction: HOME page Main state page Icon Introduction： Main Menu Icon: Tap to enter the main menu HOME interface Main State Icon: Click to enter the Main State interface Parallel Data Icon: Click to enter the Parallel Data page... - Page 11 Menu ② Menu SOC（Total） Current Voltage Main BMS INFO state Warranty page Current Parallel data Voltage BMS info Cell 01 voltage Cell 02 voltage Voltage ....Cell 16 voltage PACK Info Temperature Mos-T ENV-T Warning Home Protect BMS Status Fault Record GOOD WE PROTOCOL LV BMS Protocol (CAN) for Solar...
- Page 12 Growatt BMS CAN_Bus-protocol-low-voltage USER-485-voltron Voltronic Inverter and BMS 485 communication protocol 20200325 RS485 PYLON RS 485-protocol-pylon-low-voltag Luxpowertek Battery Protocol RS 485-V 01 English Language select Chinese （Traditional Chinese） System PACK SN (BLUETOOTH SN ) Note: The protocol list is access from the BMS motherboard. The following is an example: Based on the built-in list of each BMS motherboard, the first time you change the protocol, you need to enter the permission password, and the initial password is 123456.
-
Page 13: Instructions
4 Instructions 4.1 Packing list (Standard) Before unpacking, please check the outside of the battery for damage to the packaging and check the model of the battery. If there is any abnormality, please do not open the package and contact the after-sales service center as soon as possible. - Page 14 Installation Picture of Casters Next，you can follow these steps to install the casters： 1. Pick up one caster and four M6*14 screws； 2. Use the screws to secure the casters in the predetermined position on the lithium battery. 3. Repeat the above steps until dour casters are properly fixed in place.
-
Page 15: Packing List (Optional)
4.2 Packing list (Optional) ×2 ×1 ×2 Wall mounting bracket Wall mounting block 1 Wall mounting block 2 ×4 ×15 M10*120 expansion bolt M6×14 bolt group... -
Page 16: Installation Requirements
4.3 Installation requirements a. Space installation distance Master and check the performance of all tools and devices to ensure safety before using them. The left and right distance between battery packs is recommended. Minimize the distance as much as possible. - Page 17 b. Installation requirements 2. Make the mounting bracket close to the wall (level 1. Using sixteen M6*14 screws, install wall correction), mark the screw holes with a marker, and mounting block 1 and wall mounting block 2 then remove the mounting bracket. onto the battery pack.
- Page 18 c. Installation environment The battery works best at 20~40°C. Avoid installation in environments with direct high temperature and rain. Avoid installation close to high temperature heat source or low temperature cold source. Avoid installation in places where the ambient temperature changes drastically. ...
- Page 19 e. Wiring diagram Positive output power cable (1500mm) Negative output power cable (1500mm) RS485 communication cable (1500mm) Lithium battery positive parallel power cable Lithium battery negative parallel power cable Lithium battery parallel communication cable (DIP~BMS) (1200mm)
- Page 20 Precautions for inverter connection and parallel connection： According to the above parallel schematic diagram and 2.1 products appearance, select the correct wiring harness for connection. 1. Output power cable (black and red cables):The positive connector of the host is connected to the positive terminal of the inverter (red cable);The negative connector of the host is connected to the negative terminal of the inverter (black cable).
-
Page 21: Charging Operation
Warning 1. For operational safety and compliance, please disconnect the communication and cable link with the inverter when storing the battery. 2. During the handling and installation of the battery, it is recommended to wear safety helmets, goggles, protective shoes and other safety equipment suitable for the work to prevent accidental injury; 3. -
Page 22: Description Of Battery Parallel Capacity And Voltage
battery voltage drops to 41.6V. Note: All tests stated in this document shall be performed at 25±2℃. Precautions for charging and discharging operation： a) When the temperature is high ( ≥35 °C) in summer, the battery should not be charged more than 0.5C during the day, and it is recommended to stand for more than 30 minutes in the middle of the charge-discharge conversion to avoid the battery being used often in a high-temperature environment (a high-temperature environment will affect the battery life). -
Page 23: Protection Features
5 Protection Features Item Factory default parameter Set state Postscript Cell overcharge 3600mV settable alarm voltage Cell Cell overcharge overcharge 3650mV settable protection voltage protection Cell overcharge 1.0S settable protection delay Cell overcharge cell 3380mV settable protection voltage over-voltage SOC＜96% protection SOC release settable... - Page 24 Battery over-discharge 44.8V settable alarm voltage Battery Overall over-discharge 43.2V settable over-discharge protection voltage protection Battery over-discharge 1.0S settable protection voltage delay Battery Battery over-discharge 47.2V settable over-discharge protection release protection voltage release Release on charge Plug in the charger to activate Charging over-current alarm 105A...
- Page 25 Discharge over-current 1 1.0S settable Protection delay Discharge Automatic Automatically disconnects after 1 minute over-current 1 disconnect protection Charge disconnect Discharge current > 1A release Discharge Protection current settable It can be set 10 ＞150A consecutive over-current 2 Protection delay 500mS settable occurrences to lock...
- Page 26 Charging high 65℃ temperature settable protection Charge high 55℃ temperature settable protection release Discharge low -15℃ settable temperature alarm Low temperature -20℃ discharge settable protection Discharge low -15℃ temperature settable protection release High discharge 65℃ settable temperature alarm Discharge high 70℃...
- Page 27 Ambient high 75℃ temperature settable protection Ambient high 65℃ temperature settable protection release Low battery Low battery alarm No alarm when SOC＜5% settable alarm condition charging Sleep voltage 3150mV settable Delay time 5min settable Sleep function Charging and Cell voltage voltage difference＞1V settable discharging are not...
-
Page 28: Specifications
6 Specifications LFP14.33KWH51.2V-P65F1 Parameter LiFePO Battery Type 51.2V Nominal Voltage 280Ah Nominal Capacity 14336Wh Energy 100A Continuous Discharge Current 57.6V Charge Cut-off Voltage 41.6V Discharge Cut-off Voltage 100A Maximum Charge Current 200A@30min Maximum Discharge Current 240A@10S Peak Discharge Current 100A Recommend Discharge Current 50.88~53.6V... -
Page 29: Precautions
7 Precautions 7.1 Maintenance precautions Item Cycle If the battery is not in use, it needs to be fully charged 3 months and discharged to 50%. Check whether the wall bracket installation is loose. 6 months Please tighten the appropriate position if available. Check the casing for damage. -
Page 30: Disclaimers
8 Disclaimers The warranty does not apply to the following conditions: Damage caused by improper use or inappropriate environments (It is strictly forbidden to install the Energy Storage System in the humid, salt spray, corrosive, greasy, flammable, explosive, dust accumulative or other harsh environments). - Page 31 HUIZHOU EPEVER TECHNOLOGY CO., LTD BeiJing Service Hotline：010-82894896/82894112 Huizhou Service Hotline：0752-3889706 Shenzhen Service Hotline：0755-89236770 E-mail：sales@epever.com Website：www.epever.com.cn...
Need help?
Do you have a question about the LFP14.33KWH51.2V-P65F1 and is the answer not in the manual?
Questions and answers