Subscribe to Our Youtube Channel
Related Manuals for Lumber Jack PRO Series
Summary of Contents for Lumber Jack PRO Series
- Page 1 SAFETY AND OPERATING MANUAL 12" PLANER THICKNESSER WITH HELICAL CUTTER HEAD ORIGINAL INSTRUCTIONS PT305H...
-
Page 2: General Safety Instructions
Technical Specification Attention: Please choose proper power source, voltage and frequency that are shown in the label for your tool. Planer / Thicknesser PT305H Motor Power 1800 W Cutting block speed 6700 RPM Helical cutting blades Planer Max. planing width 305 mm Max chip removal 3 mm... - Page 3 Do not overload the machine and only use it within the performance range specified in the chapter Technical Data of the operating manual. When working outside, do not stand on slippery ground and wear solid shoes. Do not misuse the cable. Protect it from heat, oil, and sharp edges. ...
-
Page 4: Proper Use
Always match the planer/thicknesser block protector to the work piece width. The unused part of the knife block must be covered. Use a feed stick for short work pieces. When planing narrow work pieces, use additional supports like, for instance, horizontal pressure devices or spring-loaded guards. -
Page 5: Electrical Requirements
Thrown work pieces can lead to injury if the work piece is not properly secured or fed, such as working without a limit stop. Wood chips and sawdust can be health hazards. Be sure to wear personal protective gear such as ... -
Page 6: Accessories And Attachments
Attention: There is an overcurrent protection device in the circuit for single phase model. Overcurrent protection Three-phase motors are equipped with self-resetting temperature protection, the motor will automatically stop when it overheats, and it can be turned on again after cooling. ACCESSORIES AND ATTACHMENTS RECOMMENDED ACCESSORIES To avoid injury:... - Page 7 TABLE OF LOOSE PARTS Unpack carton; check you machine to see parts listed below: 1. Planer and thicknesser 2. Fence 3. Hose 4. Hose clamp 5. Push stick 6. Fence support 7. Suction connector 8. Conversion port 9. Chip bag connector 10.
-
Page 8: Assembly And Installation
ASSEMBLY & INSTALLATION WARNING: Do not connect to power supply until assembly is complete．Failure to comply could result in accidental starting and possible serious personal injury． Assemble the box base by using 12 socket head bolts (A). Use socket head screws and flat washers mounting two swivel casters to front caster support assembly. -
Page 9: Operation
Insert the fence support C in the guide of machine, secure it using short lock handle D and clamp E. Assemble the fence to the fence support, fix these with the long lock handle F, the bolt and washer. ... - Page 10 Adjust the cutter block guard. The height can be adjusted with the knurled screw I, located under the cutter block guard arm. After releasing the locking knob J, the cutter block guard can be moved to the side and the planer adjusted to the correct width.
- Page 11 must lie firmly on the table so they can be guided safely. For short work pieces use a push stick. 2. Thicknessing Mount the suction connector for thicknessing Loosen the lock hand D, remove the fence assembly. Pull and rotate the handle L to release the table locking.
-
Page 12: Maintenance
Following the scale and using the handwheel, set the thicknessing table to the desired height. Narrow wood is introduced in the centre. Warning: In case of a defect, switch off the machine at once. Do not remove any chips or splinters from the tables while the machine is running. - Page 13 Before installing each screw, lightly coat the screw threads with machine oil and wipe off any excess. Securely tighten each screw which holds the knife inserts before operating the planer. Knife inserts should be torqued to approximately 50 to 55 inch pounds. ATTENTION: ...
-
Page 14: Troubleshoothing
TROUBLESHOOTHING PROBLEM CAUSE SOLUTION Machine cannot be switched on. No power supply. Check power supply. Circuit breaker is tripped Reset circuit breaker Carbon brush worn. Take machine to your service point. Machine switches automatically ... - Page 15 ASSEMBLY DIAGRAM...
-
Page 16: Part List
PART LIST Description QTY. Description QTY. Dust chute assembly Screw Socket head screw Spacer ring Interlock switch Set screw Switch mounting plate Infeed table Flat washer Outfeed table Socket head screw Insert Socket head screw Slot cover Lock washer Lock nut Hex nut Guide plate Wire for interlock switch... - Page 17 Description QTY. Description QTY. 5715 Socket head screw Handwheel 5716 Socket head screw Hex head bolt 5717 Flat washer Socket head screw Thickness scale Guide rod 100A Cut depth scale Flange nut Body Shaft 1001 Lock nut Kickback plate 1002 Flat washer Socket head screw 1003...
- Page 18 Description QTY. Description QTY. 123A Flat washer Sprocket support plate 123B Lock washer Idler sprocket Fan house cover Lock nut Set screw Carriage bolt Fan pulley Lock block 126A Vbelt Flat washer Sprocket Lock handle 127A Socket head screw Socket head screw 127B Cord clamp Guide bracket...
- Page 19 Description QTY. Description QTY. Large leg plate Left fence cover Connecting plate Flat washer 2011 Connecting plate Socket head screw Socket pan head screw Push stick 2031 Front caster support Reduction gear shaft 2032 Swivel caster Needle bearing 2033 Connecting lever Reduction gear 14T 2034 Rear caster support...
-
Page 20: Declaration Of Conformity
DECLARATION OF CONFORMITY We Importer: TOOLSA VE LTD Unit C, Manders Ind. Est., Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: 12" Planer Thichknesser with Helical Cutter Head Model: PT305H Complies with the following Directives: Electromagnetic Compatibility Directive - 2004/108/EC Machine Directive - 2006/42/EC Restrictions of the use of Hazardous Substances in Electrical Equipment - 2011-65/EU Waste Electrical and Electronic Equipment - 2012/19/EU...
Need help?
Do you have a question about the PRO Series and is the answer not in the manual?
Questions and answers