Related Manuals for Lumber Jack DP16-1050B
Summary of Contents for Lumber Jack DP16-1050B
- Page 1 SAFETY AND OPERATING MANUAL 16mm Bench Top Drill Press DP16-1050B ORIGINAL INSTRUCTIONS DP16-1050B...
-
Page 2: Table Of Contents
Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..Symbols & Cable Rating Chart ……….…………………………………….……… Machine Details and Product Features……….…………………………….…. Assembly…………………………………………………………………………………….. Adjustments……………………………………………………………………………….. Operation, Maintenance and Service………………………………………….. Lumberjack Guarantee………….……………………………………………………. Declaration of Conformity…………………………………………………………… Parts List…………..………………………………………………………………………... Parts Diagram……………………………………………………………………………… DP16-1050B... -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. DP16-1050B... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. DP16-1050B...
- Page 5 8.2 Do not wear gloves, ties or loose clothing. 8.3 while drilling make sure the piece is secured with a vice; never hold the workpiece by hand! Never keep your fingers near where they could touch the drill in case the piece moves suddenly. DP16-1050B...
- Page 6 9.4. The smaller the gauge number of the wire the greater the capacity of the cord. 9.5. When using a cable reel, always unwind the cable completely. DP16-1050B...
-
Page 7: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 DP16-1050B... -
Page 8: Machine Details And Product Features
Max. Distance From Chuck to the base – 630mm The design of the model may be different Table Size – 254X254mm depending on manufacturing changes. Base Size – 450X270mm Over all Height – 580mm Nett Weight - 50Kgs Gross Weight – 52Kgs DP16-1050B AIR6V AIR6V AIR6V AIR6V... - Page 9 2. Remove the protective oil that is applied to the table and column. Any ordinary grease and spot remover will do. 3. Apply a coat of paste wax to the table and column to prevent rust. Wipe all parts thoroughly with clean dry cloth. DP16-1050B...
-
Page 10: Assembly
4. Install a bolt in each hole through the column support (C) and the base and tighten with the ajustable wrench. 5.Loosen set screw (A) in column collar (B) with 3mm hex. Key (C) and remove collar and rack (D) from the column. DP16-1050B... -
Page 11: Assembly Instructions
(D) as shown in Option #2. Loosen the set screw in the crank and reposition it as close to the table support as possible. Tighten set screw in the crank handle. DP16-1050B... - Page 12 1. Lift the guard (A) from the right side and keep it opened. 2. Release the belt tension lock knobs (B) located on the both side of the drill press head. Release tension to the belt tension handle (C) clockwise. Tighten the belt tension lock knobs (B). DP16-1050B...
- Page 13 6. Close the belt guard. drilling. Turn the chuck key clockwise to tighten, 7. If the belt slips while drilling, readjust the belt counter clockwise to loosen. tension. DP16-1050B...
-
Page 14: Adjustments
2. Place workpiece on table. Adjust table until the tip of the drill is just a little above the top of the workpiece. 3. Turn the depth scale (C) clockwise until the depth scale indicator (D) points to the desired drilling depth on the scale. DP16-1050B... -
Page 15: Removing The Chuck
Make an indentation in the workpiece where you want the to drill a hole using a centre punch or a sharp nail. Before turning the switch ON, bring the drill bit down to the workpiece, lining it up with the hole location. DP16-1050B... - Page 16 If the workpiece or the back-up material are not not long enough to reach the column, clamp them to the table. Failure to do this could result in personal injury. DP16-1050B...
-
Page 17: Operation, Maintenance And Service
Simply press the Red button to stop the machine Store out of reach of children in a stable cool temperature dry place and avoid too high or too low temperatures. DP16-1050B... -
Page 18: Maintenance And Service
1. Using household detergent tapered inside surface of clean the tapered surface of spindle. It falls off when trying to chuck or on the spindles the chuck and the spindle to install it. tapered surface remove the dirt, grease and oil. DP16-1050B... -
Page 19: Lumberjack Guarantee
This letter should be then sent with proof DP16-1050B... - Page 20 This Guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer. 4. Notice This Guarantee applies to all product purchased from an Authorised Dealer of Lumberjack within the United Kingdom. Terms of Guarantee may vary in other countries. DP16-1050B...
-
Page 21: Declaration Of Conformity
Old Heath Road, Wolverhampton, WV1 2RP. Tel: 01902 450 470 Declares that the Bench Top Drill Press (DP16-1050B) Is in compliance with the regulations included in the Directives:2006/95/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by Ente Certificazione Macchine srl,Via Cà Bella 243 - Location Castello di Serravalle - 40053 Valsamoggia (Bo) ITALY (No.:2T160318.TTD0W34) -
Page 22: Parts List
Set screw (special) head Special hex. nut Tooth washer Special hex. nut Pan hd. screw 29-1 Spring & cap assembly Switch box Wire tie Pan hd. screw Cord clamp Switch plate Adjusting lever Switch Hex. bolt Ball bearing DP16-1050B AIR6V AIR6V AIR6V... - Page 23 Quill gasket Crank handle Quill Base Drift key Colum support Round table Hex. bolt Table arm w/scale Colum Table lock handle Rack Elevation worm gear Starting capacitor Helical gear Chuck guard Bracket lock handle Tapping screw DP16-1050B AIR6V AIR6V AIR6V...
-
Page 24: Parts Diagram
Parts Diagram DP16-1050B...
Need help?
Do you have a question about the DP16-1050B and is the answer not in the manual?
Questions and answers