Subscribe to Our Youtube Channel
Related Manuals for Lumber Jack DP13-580B
Summary of Contents for Lumber Jack DP13-580B
- Page 1 SAFETY AND OPERATING MANUAL 13mm Bench Top Drill Press DP13-580B ORIGINAL INSTRUCTIONS DP13-580B...
-
Page 2: Table Of Contents
Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..Symbols & Cable Rating Chart ……….…………………………………….…….. Machine Details and Product Features……….…………………………….… Assembly……………………………………………………………………………………. Adjustments……………………………………………………………………………….. Operation, Maintenance and Service………………………………………….. Lumberjack Guarantee………….……………………………………………………. Declaration of Conformity………………………………………………………….. Parts List…………..………………………………………………………………………... Parts Diagram…………………………………………………………………………….. DP13-580B... -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. DP13-580B... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. DP13-580B...
- Page 5 8.2 Do not wear gloves, ties or loose clothing. 8.3 while drilling make sure the piece is secured with a vice; never hold the work piece by hand! Never keep your fingers near where they could touch the drill in case the piece moves suddenly. DP13-580B...
- Page 6 10.4. The smaller the gauge number of the wire the greater the capacity of the cord. 10.5. When using a cable reel, always unwind the cable completely. DP13-580B...
-
Page 7: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 DP13-580B... -
Page 8: Machine Details And Product Features
255mm Table Size – 165X165mm Base Size – 280X180mm Over all Height – 580mm Dimensions (L x M x H) - 580 x 404 x 186mm Nett Weight - 15Kgs Gross Weight – 17Kgs DP13-580B AIR6V AIR6V AIR6V AIR6V... - Page 9 Wipe all parts 10. Depth Scale thoroughly with clean dry cloth. 11. Column 12. Bevel Scale 13. Table Bevel Lock 14. Table 15. Feed Handle 16. Chuck 17. Feed Stop Rod 18. Stop Nuts 19. On-Off Switch 20. Chuck Guard DP13-580B...
-
Page 10: Assembly
3. Locate three long bolts from the parts bag. 4. Install a bolt in each hole through the column support and the base and tighten with the adjustable wrench. DP13-580B... -
Page 11: Assembly Instructions
5. Tighten the belt tension lock handle. NOTE: The belt should deflect approximately 1/2” by applying finger pressure at the mid-point of the belt between the pulleys. 6. Close the belt guard. 7. If the belt slips while drilling, readjust the belt tension. DP13-580B... - Page 12 Make sure the drill bit is centred in the chuck before tightening the chuck with the key. Tighten the drill bit well, so that it doesn’t slip while drilling. Turn the chuck key clockwise to tighten, counter clockwise to loosen. DP13-580B...
-
Page 13: Adjustments
5. Retighten the table bevel lock bolt. 12. Check the quill while feeding to have a smooth and unrestricted movement. If the movement is too tight, loosen the jam nut and slightly loosen the standard nut until it is unrestricted. Retighten the jam nut. DP13-580B... -
Page 14: Operation, Maintenance And Service
Simply press the Red button to stop the machine Store out of reach of children in a stable cool temperature dry place and avoid too high or too low temperatures. DP13-580B... - Page 15 4. Chuck incorrectly installed Chuck will not stay attached to 1. Dirt, grease or oil on the 1. Using household detergent tapered inside surface of clean the tapered surface of spindle chick or on the spindles spindle and chuck. tapered surface DP13-580B...
-
Page 16: Lumberjack Guarantee
This letter should be then sent with proof DP13-580B... - Page 17 This Guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer. 4. Notice This Guarantee applies to all product purchased from an Authorised Dealer of Lumberjack within the United Kingdom. Terms of Guarantee may vary in other countries. DP13-580B...
-
Page 18: Declaration Of Conformity
Old Heath Road, Wolverhampton, WV1 2RP. Tel: 01902 450 470 Declares that the Bench Top Drill Press (DP13-580B) Is in compliance with the regulations included in the Directives:2006/95/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by Ente Certificazione Macchine srl,Via Cà Bella 243 - Location Castello di Serravalle - 40053 Valsamoggia (Bo) ITALY (No.:2T160318.TTD0W34) -
Page 19: Parts List
Pan hd screw Cord clamp Switch housing Pan hd screw Pan hd screw Foam washer Switch Head Self tapping screw Nylon hex. nut Switch plate cover Washer Switch safety key Hex. bolt Wire connector Motor pulley Spring seat DP13-580B AIR6V AIR6V AIR6V... - Page 20 Power cord Table support Quill gasket Lock handle Ball bearing Column Quill Base Pan hd screw Hex. bolt Stop collar Hex. bolt Retaining ring/shaft Table Spindle Hex. key (3mm) Chuck Hex. key (4mm) Chuck guard Chuck key DP13-580B AIR6V AIR6V AIR6V...
-
Page 21: Parts Diagram
Parts Diagram DP13-580B... - Page 22 Parts Diagram DP13-580B...
Need help?
Do you have a question about the DP13-580B and is the answer not in the manual?
Questions and answers