Related Manuals for JEI DRILLING & CUTTING SOLUTIONS MAGBEAST LP45
Summary of Contents for JEI DRILLING & CUTTING SOLUTIONS MAGBEAST LP45
- Page 1 SAFETY INSTRUCTIONS AND OPERATORS MANUAL FOR DRILLING MACHINE MAGBEAST LP45 UNIT 21 EMPIRE BUSINESS PARK, ENTERPRISE WAY, BURNLEY LANCASHIRE BB12 6LT Tel. +44 1706 229490 www.jeiuk.com e-mail: sales@jeisolutions.co.uk...
-
Page 2: Table Of Contents
C E DECLERATION OF COMFORMITY ........Error! Bookmark not defined. MACHINE TEST CERTIFICATE ..................... - 19 - WARRANTY CARD ........................- 3 - BEFORE YOU START WORK WITH THE MACHINE, PLEASE READ THESE INSTRUCTIONS CAREFULLY AND USE ALL RECOMMENDATIONS. Operators’ manual for Drilling Machine Magbeast LP45 - 2 -... -
Page 3: General Information
2 inch steel, in one pass and with precision not otherwise attainable without heavy stationary equipment. The MAGBEAST LP45 machine is capable of milling 40 mm holes through 2 inch plate what is totally unique for an electromagnetic drill of that size and weight. The MAGBEAST LP45 is equipped with a powerful verified for many years of exploitation drive and electromagnet with field control system. -
Page 4: General Safety Advice
In all cases always use a safety chain/strap /see drawing 1/. The safety chain mustn't be loose! To avoid this situation the safety chain should be wrapped around the element it is hooked to. Operators’ manual for Drilling Machine Magbeast LP45 - 4 -... - Page 5 Check whether any of the parts are broken and that all the parts are fastened properly. Make sure to maintain proper conditions affecting work of the machine. Operators’ manual for Drilling Machine Magbeast LP45 - 5 -...
-
Page 6: Standard Equipment
Before every positioning, wipe working surface with coarse-grained sandpaper. Please keep all recommendations. 3. STANDARD EQUIPMENT MAGBEAST LP45 comes in a standard equipment set which consists of: metal box - 1 pc drilling machine - 1 pc... -
Page 7: Start Up And Operation
A few types of holes that can be done with a milling cutter Basically milling cutters are designed to make through holes. On occasions when there is a need for an overlapping hole pilot should not be used. Operators’ manual for Drilling Machine Magbeast LP45 - 7 -... - Page 8 Raise the drive and the slide (1) up using the lever (3); b) Raise the guard in order to attain access to the arbor (4) screws (5). c) Loosen the screws (5); d) Remove the arbor (4). Operators’ manual for Drilling Machine Magbeast LP45 - 8 -...
- Page 9 2. Raise the guard in order to attain access to the arbor (4) screws (3). 3. Loosen the screws (3); Remove the milling cutter (6) and the pilot (5) from the arbor socket (4). Operators’ manual for Drilling Machine Magbeast LP45 - 9 -...
- Page 10 To move machine into next drilling spot, stop the motor as described above and push the mains switch to the position. CAUTION: READ THE WHOLE INSTRUCTION MANUAL BEFORE ATTEMPTING TO START UP Operators’ manual for Drilling Machine Magbeast LP45 - 10 -...
- Page 11 It may take a few seconds for cooling liquid to fill the whole system. - Turn the motor on. Operators’ manual for Drilling Machine Magbeast LP45 - 11 -...
- Page 12 7, detailed guide is supplied by manufacturer of used drilling tools. The graph is just a general guide and the shown dependence applies to average structural steel. One Operators’ manual for Drilling Machine Magbeast LP45 - 12 -...
- Page 13 “O” (It causes the motor off, the magnet still holds). To move on the machine to drill in another place you should stop the motor and then push on the main switch in position “I”. Operators’ manual for Drilling Machine Magbeast LP45 - 13 -...
- Page 14 JEI DRILLING & CUTTING SOLUTIONS LTD 4.9 Replacement of motor brushes: For the MAGBEAST LP45 drill, the state of the carbon brushes should be monitored every 100 working hours. Replacement of motor brushes should take place when the machine is turned off and the power cable is disconnected from the power grid! 1.
-
Page 15: Maintenance And Service
- work should be terminated immediately and the machine should be sent to service for inspection as soon as possible. Operators’ manual for Drilling Machine Magbeast LP45 - 17 -... - Page 16 HM50 DIAGRAMS COMPLETE LP45 DIAGRAMS COMPLETE...
- Page 17 Parts List for JEI MagBeast LP45 LP45-01 LP45-01 LP45-23 LP45-12 LP45-02 LP45-24 LP45-13 AIR35-27 HM50-07 LP45-25 LP45-04 LP45-26 LP45-14 HM50-03A LP45-15 HM50/100-PCB LP45-SHAFT HM40.EX-MC/1 HM50-11 LP45-29 LP45-29 HM100-34 HM100-34 LP45-07 LP45-07 LP45-30 LP45-21 LP45-08 LP45-19 LP45-32 LP45-SPD LP45-09 LP45-27 LP45-AB...
- Page 18 www.jeiuk.com MOTOR DIAGRAM.
- Page 19 www.jeiuk.com MOTOR DIAGRAM PARTS LIST. No DESCRIPTION PART NUMBER PIECES Cap Screws HC 4, 8x50 HM40.EX-01 Motor Top Cap HM40.EX-02 Brusholder Assembly HM56 Carbon Brush 6,3,10x18 HM57 Brusholder Mount Screw ZM4x12 HM111 Washer HM109 Motor Housing HM40.EX-07 Field Coil HM40.EX08 (220V) / HM40.EX08/1 (110V) Screw HM543 Fan Ring...
- Page 20 Unit 21, Empire Business Park, Enterprise Way, Burnley, Lancashire, UK, BB12 6LT Declare with full responsibility that product: MAGBEAST LP45 DRILLING MACHINE WITH ELECTROMAGNETIC BASE which the declaration applies to is in accordance with the following standards: EN 62841-1:2015, EN 55014-1:2017, EN ISO 12100:2010,...
- Page 21 1000 V and frequency 50 Hz Resistance of the protective circuit [Ω] The above-mentioned product meets the requirements of safe usage as prescribed in standard IEC-745 Name of tester ____________________ Quality Control ____________________ Operators’ manual for Drilling Machine Magbeast LP45 - 18 -...
-
Page 22: Warranty Card
Date of Production .......... Serial No ..........Quality Control: ......................Date of Purchase: ......................Signature of Seller: ………………………………………………………………………….. Operators’ manual for Drilling Machine Magbeast LP45 - 19 -...
Need help?
Do you have a question about the MAGBEAST LP45 and is the answer not in the manual?
Questions and answers