BenQ MX560 Manual
![]()
Introduction
The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands.
Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions.
Wire arrangement
Wire Arrangement |
P1 | Color | P2 |
1 | Black | 1 |
2 | Brown | 3 |
3 | Red | 2 |
4 | Orange | 4 |
5 | Yellow | 5 |
6 | Green | 6 |
7 | Blue | 7 |
8 | Purple | 8 |
9 | Gray | 9 |
Case | Drain wire | Case |
RS232 pin assignment
Pin | Description | Pin | Description |
1 | NC | 2 | RXD |
3 | TXD | 4 | NC |
5 | GND | 6 | NC |
7 | RTS | 8 | CTS |
9 | NC | | |
Connections and communication settings
Choose one of the connections and set up properly before RS232 control.
RS232 serial port with a crossover cable
![BenQ - MX560 - RS232 serial port with crossover cable connection RS232 serial port with crossover cable connection]()
Settings
On-screen images in this document are for reference only. The screens may vary depending on your Operating System, I/O ports used for connection, and the specifications of the connected projector.
- Determine the COM Port name used for the RS232 communications in Device Manager.
![BenQ - MX560 - RS232 with crossover cable setup - Step 1 RS232 with crossover cable setup - Step 1]()
- Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected.
![BenQ - MX560 - RS232 with crossover cable setup - Step 2 RS232 with crossover cable setup - Step 2]()
- Finish Serial port setup.
![BenQ - MX560 - RS232 with crossover cable setup - Step 3 RS232 with crossover cable setup - Step 3]()
Baud rate | 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu. |
Data length | 8 bit |
Parity check | None |
Stop bit | 1 bit |
Flow control | None |
RS232 via LAN
![BenQ - MX560 - RS232 via LAN connection RS232 via LAN connection]()
![BenQ - MX560 - RS232 via LAN connection setup RS232 via LAN connection setup]()
Settings
- Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network.
- Input 8000 in the TCP port # field.
RS232 via HDBaseT
![BenQ - MX560 - RS232 via HDBaseT connection RS232 via HDBaseT connection]()
Settings
- Determine the COM Port name used for the RS232 communications in Device Manager.
- Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected.
![BenQ - MX560 - RS232 via HDBaseT setup - Step 1 RS232 via HDBaseT setup - Step 1]()
- Finish Serial port setup.
Baud rate | 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu. |
Data length | 8 bit |
Parity check | None |
Stop bit | 1 bit |
Flow control | None |
Command table
![information]()
- Available features differ by projector specification, input sources, settings, etc..
- Commands are working if the standby power is 0.5W or a supported baud rate set. of the projector is
- Uppercase, lowercase, and a mixture of both types of characters are accepted for a command.
- If a command format is illegal, it will echo Illegal format.
- If a command with correct format is not valid for the projector model, it will echo Unsupported item.
- If a command with correct format cannot be executed under certain condition, it will echo Block item.
- If RS232 control is performed via LAN, a command works whether it starts and ends with <CR>. All the commands and behaviors are identical with the control through a serial port.
![BenQ - MX560 - Command table - Part 1 Command table - Part 1]()
![BenQ - MX560 - Command table - Part 2 Command table - Part 2]()
![BenQ - MX560 - Command table - Part 3 Command table - Part 3]()
![BenQ - MX560 - Command table - Part 4 Command table - Part 4]()
![BenQ - MX560 - Command table - Part 5 Command table - Part 5]()
![BenQ - MX560 - Command table - Part 6 Command table - Part 6]()
![BenQ - MX560 - Command table - Part 7 Command table - Part 7]()
![BenQ - MX560 - Command table - Part 8 Command table - Part 8]()
![BenQ - MX560 - Command table - Part 9 Command table - Part 9]()
![BenQ - MX560 - Command table - Part 10 Command table - Part 10]()
FAQ Video
- How to use RS232 cable to do volume control and sound control on projector?
https://youtu.be/P4F26kEv60U - How to use RS232 cable connection to power on & off projector?
https://youtu.be/faGUvcDBmJE -
How to set up RS232 cable connection
https://youtu.be/CYJRqyO6K1w
- How to use RS232 command to request fan speed and temperature value?
https://youtu.be/KBXEd-BCDKQ
BenQ.com
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download BenQ MX560 Manual
Need help?
Do you have a question about the MX560 and is the answer not in the manual?
Questions and answers