1. Manuals
  2. Brands
  3. FJM security Manuals
  4. Locks
  5. Combi-Cam E 7910
  6. Programming instructions manual

FJM security Combi-Cam E 7910 Programming Instructions Manual

Electronic cabinet lock
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

PROGRAMMING INSTRUCTIONS
PROGRAMMING THE LOCK CODE
Code Levels
The Combi-Cam E has three potential code levels:
1. User code
2. Service code - (By default this is not active)
3. Master code
Before installing the lock, it is strongly recommended to change both the user and master codes. Be
sure to record the new codes and store them in a secure location.
Important: If the codes are lost or forgotten, the lock cannot be opened. There are no override codes
or recovery methods available. To avoid permanent lockout, safeguard your codes carefully.
Use Modes
1. Individual Mode (Default): In this mode, a single user-defined code is used to open the lock. This
mode is ideal for personal or assigned-use applications.
2. Locker Mode (One-Time-Use): Locker mode is designed for shared-use environments such as
gyms, employee lockers, or amusement parks. Similar to hotel safes, the lock allows any user to
input a personal code while the lock is open. This code becomes the active access code and will
unlock the lock upon the user's return. After reopening, the lock resets and is ready for the next
user. To set up Locker mode, see the instructions on Page 7.
User Code
Opening the Lock (User Code Access)
The factory default user code is 1-0-1-0.
To unlock:
1. Enter the 4-digit user code.
2. Within 5 seconds, rotate the handle
in the opening direction.
3. The lock will emit a confirmation
beep and the green LED will flash,
indicating successful access.
Combi-Cam E - Electronic Cabinet Lock
Changing the User Code (Individual
Mode Only)
1. Press the * (star) button.
2. Enter the current 4-digit user code.
3. Press * again, then enter your new
4-digit code.
4. Press * one final time to confirm.
A confirmation beep and green LED
flash will indicate that the new code
has been set successfully.
206-363-3290 | 800-525-0954
www.fjmsecurity.com
© 2025 Olympus Lock, Inc.
www.fjmsecurity.com
7910 (K10 / K10P)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Combi-Cam E 7910 and is the answer not in the manual?

Questions and answers

Related Manuals for FJM security Combi-Cam E 7910

Summary of Contents for FJM security Combi-Cam E 7910

  • Page 1 www.fjmsecurity.com 7910 (K10 / K10P) PROGRAMMING INSTRUCTIONS Combi-Cam E - Electronic Cabinet Lock PROGRAMMING THE LOCK CODE Code Levels The Combi-Cam E has three potential code levels: 1. User code 2. Service code - (By default this is not active) 3.

  • Page 2: Code Levels

    www.fjmsecurity.com 7910 (K10 / K10P) Combi-Cam E - Electronic Cabinet Lock CODE LEVELS Service Code Opening the Lock (Service Code Access) The factory default service code is 1-0-1-0-1. To unlock using the service code (when enabled in the program menu): 1.

  • Page 3: Programming Instructions

    www.fjmsecurity.com 7910 (K10 / K10P) Programming Instructions WARNINGS General Warnings • Read the Manual: Please read the full user manual before operating the lock to ensure proper setup and use. • Change Default Codes: Replace all factory-set codes with your own secure codes before installation.

  • Page 4: Program Menu

    www.fjmsecurity.com 7910 (K10 / K10P) Combi-Cam E - Electronic Cabinet Lock PROGRAM MENU Programming Please remember to record your code(s) immediately after programming. Do not store the codes inside the cabinet or drawer where the lock is installed. If the codes are lost or forgotten, there is no way to open the lock.
  • Page 5 www.fjmsecurity.com 7910 (K10 / K10P) Programming Instructions Program Setting Options Definition Example Restores Sets the user password to factory default 1-0-1-0. Default #XXXXXX* 4 0 User Code Service code not active. #XXXXXX* 5 0 Deactivate service code Service Code Activates the service code, which defaults to 1-0-1-0-1 #XXXXXX* 5 1 Activation until changed.
  • Page 6 www.fjmsecurity.com 7910 (K10 / K10P) Combi-Cam E - Electronic Cabinet Lock PROGRAM MENU Accessing the Program Menu To adjust a program setting, press the # button, enter the 6-digit master code, then press the * button. Next, enter the program number followed by the desired setting.
  • Page 7 www.fjmsecurity.com 7910 (K10 / K10P) Programming Instructions PROGRAMMING THE miniK 10 The miniK 10 can be customized from factory default settings tailored to your needs. ACCESSING THE PROGRAM MENU: Press the button and then enter the 6-digit master password. Press the button.

  • Page 8: Maintenance

    www.fjmsecurity.com 7910 (K10 / K10P) Combi-Cam E - Electronic Cabinet Lock MAINTENANCE, BATTERY CARE, & LOCKER MODE Maintenance • Clean the front of the lock with a soft, damp cloth with mild detergent, if needed. • Avoid abrasive or scratching cleaners. •...

This manual is also suitable for:

K10K10p

Table of Contents