Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BLUM MSP
Summary of Contents for BLUM MSP
-
Page 2: Table Of Contents
TABLE OF CONTENTS SEITE: Understanding this manual Safety Rules: Read Before operation! Description of parts Initial machine set-up • Unpacking and assembly of machine • Connection of air supply • Connection of electrical power supply Drilling of hinge pattern Addendumn •... -
Page 3: Understanding This Manual
Understanding this Manual Understanding this Manual Symbols and their descriptions: • Read the manual and the Safety Rules completely before you start Indicates important safety operating! rules which must be followed! • To better identify the machine components, fold out the front section of this manual. -
Page 4: Safety Rules
Do not operate this machine until you have read and understood the instruction manual and have been checked out by a qualified instructor. For a free replacement instruction manual call Blum USA at 1-800-438-6788 or Blum Canada at 1-905-670-7920. when operating this machine. - Page 5 Safety Rules for USA and Canada only DANGER • Never move your hands in the area of pinch points. ATTENTION Max. load • Maximum load onto control box is 5 CAUTION 10 lbs. (5 kg) max: 5 kg kg or 10 lbs. Charge maximale DO NOT OVERLOAD! 10 lbs.
- Page 6 • For any question or problem with the manual or Blum Sales literature. machine, contact the Blum Customer Service Department: • Noise emmission levels as per EN 31202(31204), resp.
-
Page 7: Description Of Parts
Description of Parts Description of Parts E1 ... Depth adjustment screw A 1 ... Hex-cap screw E2 ... Clamping lever (Fencing system) (Fencing system) A 2 ... Fencing system A 3 ... Base ruler H 1 ... Air filter H 2 ... Drain screw C 1 ... -
Page 8: Initial Machine Set-Up
Initial machine set-up Unpacking and assembly of machine 2. Installation of base Ruler (A3) Important: Fold out the first page at the • Loosen both hex-cap screws (A1) front of the instruction manual on the Fencing System (A2). for easier identification of the described parts. -
Page 9: Connection Of Air Supply
Initial machine set-up Connection of air supply 3. Attach worktable Warning! When turning on the air a) worktable MZA.1000.01 (not included supply, drillhead will move with machine) b) How to build your own work table is expained on page 15 1. -
Page 10: Connection Of Power Supply
Initial machine set-up Connection of power supply Warning! Warning: The electrical connection To avoid serious injury stay must be performed by a clear of drilling area and all qualified electrician. pinch points! 1. Electrical connection 2. Check motor direction • Set Main switch to position 0 (off) •... -
Page 11: Drilling Of Hinge Pattern
Drilling of hinge pattern Drilling of hinge pattern 22,5 22,5 Ø8 Ø35 Ø8 57 mm 2. Install drill-bits 1. Drill-bit length • Set Main switch to position 0 • The total length of the drill-bits (from bit-tip to adjustment screw) must be •... - Page 12 Drilling of hinge pattern 4. Correcting drilling depth Warning: To avoid serious injury stay • The drilling depth is adjusted by clear of drilling area and all turning the depth adjustment screw pinch points! (E1) • Turning screw (E1) clockwise means 3.
- Page 13 Drilling of hinge pattern 5. Adjustment of fencing system (A2) 6. Adjust positioning stops • Loosen set screw (E2) • Adjust Positioning Stops to the desired position on the Base Ruler and tighten with set screw • Adjust fencing system (A2) to required measurement •...
- Page 14 Drilling of hinge pattern Warning! To avoid serious injury stay clear of drilling area and all pinch points. Make sure that no objects are on the worktable, except panel to be drilled! 8. Drilling • Set Main switch to position 1 •...
-
Page 15: Addendumn
(Diagram is inside the motor terminal) 2. Other defects and errors • For all other defects please call the BLUM Customer Service Department (The telephone numbers are listed in the front section of this manual) Ohne Namen-6 18.11.1998, 15:00 Uhr... -
Page 16: Technical Data
Addendumn Technical Data Voltage: see serial number tag Weight: 41kg (90 lbs) without table Power: 3-phase 1,2kW Measurements: single-phase 1,2kW height = 650mm (26") widht 800mm (32") depht = 800mm (32") RPM: see motor tag Pressure requirements: 5-7bar (75-100 psi) at 4 cfm How to build your own work table 198.5 198.5... -
Page 17: Limited Warranty
Any damages under this warranty shall be limited to a maximium of the purchase price of the machine. Should any defect be found in the machine, please submit to Blum, in writing, the reference number, the serial number, and the name of the distributor from whom the machine was purchased. -
Page 18: Ec-Declaration Of Conformity
The following standards have been used to build the machine in conformance to the above EC-Guideline: EN 292 part1 and part2, EN 60 204 part1, EN 31202(31204), EN 294, EN 349 Höchst, 20.12.94 Blum Lothar Quality Assurance Manager ppa. Blum Egon Technical Director Ohne Namen-6 18.11.1998, 15:01 Uhr... - Page 19 Addendumn Notice Ohne Namen-6 18.11.1998, 15:01 Uhr...
- Page 20 Addendumn Notice Ohne Namen-6 18.11.1998, 15:01 Uhr...
- Page 21 Addendumn Notice Subject to change without notice! Id. Nr. 120.066.0 Printed in Austria BA-13.02 E / 01.95 Ohne Namen-6 18.11.1998, 15:01 Uhr...
Need help?
Do you have a question about the MSP and is the answer not in the manual?
Questions and answers