PowerLocus P2 Manual

PRODUCT INDICATION

1. Power on /off
2. play/pause, answer/end calls, reject call, last number redial
3. Volume up (Short Press)
   Next song (Long Press)
4. Volume down (Short Press)
   Last song (Long Press)
5. Multi-function search radio)
6. Headset jack
7. LED indicator
8. USB-C charging port
9. Microphone
10. Micro SD/TF card slot

SPECIFICATIONS

Bluetooth Version: V5.3
Working Distance Range: 10M
Frequency Range: 20Hz-20kHz
Audio Drivers: Ф40mm
Charging Voltage: DC 5V
Charging Time: About 1.5 Hours
Talking/Music Time: About 20 Hours (50% Volume)
Impedance: 32 Ohrns
Weight: 175g/0.39LBs
Volurne Sensitivity: 100+/-3dB
Bluetooth Specification Power: Class 1
Frequency band: 2.402-2.480GHz
Operating frequency: 2.402-2.480M Hz
Rated power consumption: 120 mw
Maximum output power: < 7dBm
Operating Temperature: 0ºC to 45ºC

POWER ON/OFF THE HEADSET

• POWER ON: Slide the switch right and the blue and red indicator light will flash (the headset said: the wireless is ready to pair ).
• POWER OFF: Slide the switch left and blue indicator light will go off.

PAIR TO YOUR MOBILE PHONE OR OTHER PRODUCTS

• Slide the switch right and the blue and red indicator light will flash (the headset said: the wireless is ready to pair ).
• Turn on the bluetooth function of your phone or other products.
• Search for the bluetooth devices and select "PowerLocus P2 ". (Enter the code '0000' if needed)
• If paring is successful, the blue light indicator will be steady
• Please make sure the headphone is working before pairing.
• It will connect to the pre-set phone automatically when turns on(Please make sure the bluetooth function of your phone is working)
• If the pairing is not successful, please switch off headset firstly, and then re-pair again.

EQ Modes (Bass, Rock, Pop, Vocal Mode)

In powered-on mode, click the M button to switch between the modes - Rock, Bass, Pop and Vocal

MP3/FM

• In power-on mode, insert the TF card, MP3 will play automatically.
• If have not TF card, short press button, twice FM radio will play automatically.
• (1) In power-on mode, short press button twice, FM radio will play automatically.
  (2) Long press the Play/Pause button to auto search all radio station,
  (3) wait for 40sec to 1min for the stations to be memorized,
  (4) then long press or, you will listen to any radio station you like.
• If you are listening to FM radio, short press button, it will be converted to the bluetooth mode. And auto connected to your phone or other products.

ANSWER/END CALLS, REJECT CALL, LAST NUMBER REDIAL

(In the bluetooth mode)

• When there is a call, short press button can answer the call. After the call, press button can hang up. If the other side hang up, no need to press the button.
• reject call: long press button about 2-3sec.
• last number redial: press fast button 2 times
• When the phone call out or answer the call, if the bluetooth headphone are playing the music, the music will pause automatically and enter the waiting state. After hang up, the music will continue to play automatically.

CHARGING THE HEADSET

• Insert USB charging cable into USB port which have support 5V power (such as AC/DC USB adapter or PC USB port). When the red light is on, the headset is in charging. When the red light will be off, the headset is fully charged. It takes about 2-2.5 hours to charge the headset fully.
• The battery is rechargeable.
  Low-Voltage alert: When the alert tone 'low battery' sounds and the indicator turns into red indicate that the battery has run out, need to be charged as soon as possible. First time charging: please be sure the battery has been charged fully before use.

WIRED HEADPHONE FUNCTION

For any mode of headphone, you can connect one side of 3.5 stereo sound supply extension line to headphone audio jack, the another side connect to Audio jack (such as mobile phone, computer, |pad etc). Then you will hear songs from other devices.

HOW TO RESET THE HEADPHONES?

Hold both Buttons for 4-7 seconds in order to reset the bluetooth and enter pairing regime again.

Safety Precautions

Please DO NOT use adapters more than DC5V 1A! Please use the original cable supplied with the package as different cables could harm the product and void its warranty.

Do not use the unit while walking, driving, or cycling. Doing so may cause traffic accidents.

Do not use in hazardous areas unless the surrounding sound can be heard. The unit is not waterproof. If water or foreign matter enters the unit, it may result in fire or electric shock. If water or foreign matter enters the unit, stop use immediately and contact PowerLocus. In particular, be careful in the following cases:

• When using the unit near a sink or liquid container. Be careful that the unit does not fall into a sink or container filled with water
• When using the unit in the rain or snow, or in humid conditions.

If you touch the unit with wet hands, or put the unit in the pocket of a damp article of clothing, the unit may get wet.

Never insert the USB plug when the headphone or charging cable is wet. If the USB plug is inserted while the unit or charging cable is wet, a short circuit may occur due to liquid (tap water, seawater, soft drink, etc.) or foreign matter on the unit or charging cable, and cause abnormal heat generation or malfunction.

Safety Instructions

• Please charge the headphones before first time using.
• Please charge at least once every 3 months to keep battery in good condition.
• To protect your hearing, please do not use the headphones long time with too high volume.
• Do NOT expose the headphone to hot temperature
• Protect from shocks and drops
• Do NOT try to open the product
• Do NOT expose to moisture, rain and liquids

For Warranty or Problems with the product, please contact us!
Email Support: info@powerlocus.com

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download PowerLocus P2 Manual