Advertisement
Quick Links
Advertisement
Related Manuals for Solus Hemi
Summary of Contents for Solus Hemi
- Page 1 FIRE FEATURES Care and Maintenance...
- Page 2 Solus Care and Maintenance Guide Congratulations on the purchase of your Solus Fire Feature. As with any other appliance, you must take good care of your outdoor fire pit to ensure longevity and reliable performance. Following this Care and Maintenance Guide will also ensure that your warranty will be in effect in the unlikely event that it should be required.
- Page 3 MANUAL LIT SYSTEM Burner Nozzles – *Vacuum (using shop vac or vacuum cleaner) tip of each nozzle to clean out any dust, dirt or water condensation in the gas orifice. Ball Valve – *Spray one shot of WD40 into the key hole, insert the key and rotate the ball valve clockwise and anticlockwise.
- Page 4 Manual Lit System w/Flame Supervision Maintenance continued… Flame Supervision Valve H15 button (grey in color). Note the pattern on the back of button for reinstallation Thermocouple K17 – *Gently clean the tip with steel wool to remove tarnish. Thermocouple viewed from the top www.solusdecor.com UK, EU: www.solusdecor.co.uk...
- Page 5 Manual Lit System w/Flame Supervision Maintenance continued… Universal Pilot J985 – *Clean the spark rod tip with steel wool to remove any tarnish or dirt. ***If gas flow weakens over time remove inlet and wash with mineral spirits and clean inside the inlet tube. Inlet Tube pictured below the Universal Pilot ELECTRONIC IGNITION SYSTEM with or without ADJUSTABLE BALL VALVE (Adjustable Auto Firepits)
- Page 6 Electronic Ignition System Maintenance continued… Picture shows one of two coil terminals. Both coils must be kept clean Intermittent Pilot J996 – *Clean the spark rod tip with steel wool to remove any tarnish or dirt. ***If gas flow weakens over time remove inlet and wash with mineral spirits and clean inside the inlet tube.
- Page 7 Electronic Ignition System Maintenance continued… Sensor Assembly (Temperature Sensor Probe) Y75 – *Clean the tip with steel wool to remove any tarnish or dirt. Temperature Sensor Probe Spark Ignitor – *Clean the tip with steel wool to remove any tarnish or dirt. Picture of Spark Ignition is shown to the left.
- Page 8 Electronic Ignition System Maintenance continued… Condensation Chamber (the vertically mounted brass tubing with end cap) – ***Remove the end cap and drain off any water. Install the end cap with fresh Teflon tape and check for gas leak. Pointing at the endcap of Condensation Chamber ETHANOL BURNERS –...
- Page 9 Beeswax referenced below Firetable, Halo, Elevated Halo, Concrete Ring (Hemi) It is important to note that the above method (under Hemi, Firecube… etc.) should not be used on any of our firepits that have a tabletop surface (including the concrete ring which is an additional option for the Hemi above) We highly recommend using placemats or coasters on any Solus table surface.
- Page 10 If you live in a high-humidity area, you may notice that your cover may become covered with moss. Solus covers can be put in the washing machine with a non-bleach laundry detergent. Hang to dry. (If you have a “tented cover” for the Halo Series, or Firetable etc., please remember to remove the rods from the casings prior to putting into the...
- Page 11 HARDWOOD TABLETOPS If you have one of our beautiful hardwood tabletops as pictured above, teak oil, Swedish oil, or other oils used for hardwood will revitalize it. These can be purchased at any hardware store in your area. Care: It is important to apply oil to your hardwood tabletop away from your firepit. Concrete is very porous and absorptive by nature so make sure that the oil does not come in contact with the concrete.
- Page 12 This metal ring is produced from a high-grade aluminum alloy with stainless steel screws. All parts are corrosion free and can be left outside along with your Hemi firepit. The aluminum has been hard anodized to help resist scratching, but it still may be susceptible to damage from small sharp objects or abrasive items being dragged across the surface.
- Page 13 Our fire stones are made exclusively for Solus, by hand in Canada. Please note that our fire stones are available for purchase with a Solus Fire pit or to clients who already own one. If you feel, during the installation of your firepit, that you would like the look of more firestones, please contact us directly.
-
Page 14: Tank Table
The tank table makes an attractive end table in your seating area. Care: Please refer to Solus Fire Features / Care and Maintenance on page 9 of 9 under “General Maintenance of the concrete vessel”. For the tabletop portion of the tank table, please make sure to follow the care guide for firepits that have tabletop surfaces.
Need help?
Do you have a question about the Hemi and is the answer not in the manual?
Questions and answers