Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Solus Manuals
  4. Outdoor Fireplace
  5. PACIFIC RIM
  6. Assembly instructions manual

Solus PACIFIC RIM Assembly Instructions Manual

Water ring
Hide thumbs

Advertisement

Quick Links

Download this manual
Fire Features
Thanks for purchasing a Solus
PACIFIC RIM water ring.
This manual provides instructions on
how to insert a PACIFIC RIM water ring
into an existing HEMI 36 firepit (manual
light). If you are setting up a whole sys-
tem from scratch, please read the full
HEMI INSTALLATION &
OPERATIONAL MANUAL first and use
this as a supplemental guide.
IMPORTANT!
TURN OFF MAIN GAS SUPPLY AND
ELECTRICITY (if you have an electric
start) BEFORE INSTALLING THIS PROD-
UCT.
GENERAL TIPS:
Your HEMI firepit will need to be level
in both directions.
Use shims at bottom of bowl to
achieve this.
Vacuum all debris off burner plate.
The tank needs to sit flat and level on
the burner plate.
You will need a drill, screwdriver and
wire strippers as well as a level and
some shims.
version: 2019.11.14
ASSEMBLY INSTRUCTIONS FOR PACIFIC RIM WATER RING
(for manual lit Hemi 36 firepit)
WARNING!
Some pieces are heavy with sharp edges. Use extreme care when lifting and assembling.
OUCH!
1
Watch for sharp edges.
ANSI Z21.97-2014
CSA 2.41-2014
EN 509:2000
EN 60335-1:2001
DANGER! HEAVY!
CE / CSA & ANSI
Lift pieces with care.
CERTIFIED
0558
OUTDOOR USE ONLY.

Advertisement

loading
Need help?

Need help?

Do you have a question about the PACIFIC RIM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Solus PACIFIC RIM

Summary of Contents for Solus PACIFIC RIM

  • Page 1 PACIFIC RIM water ring. This manual provides instructions on OUTDOOR USE ONLY. how to insert a PACIFIC RIM water ring into an existing HEMI 36 firepit (manual light). If you are setting up a whole sys- tem from scratch, please read the full HEMI INSTALLATION &...

  • Page 2: Parts List

    Fire Features CONFIRM YOU HAVE ALL PIECES Parts list: SHOWN. 1. Inner Finishing Ring Stainless steel w black coating. 1. Inner Finishing 2. Reflector Plate Ring Brushed stainless steel w/ protective plastic coating (to be removed be- fore use). 2. Reflector Plate 3.

  • Page 3: Moving & Placing

    Fire Features MOVING & PLACING Pick up by plate supports Lift and move the Water Tank by grab- bing the Reflector Plate Supports. Reflector Plate Supports Please be careful of the Outer Finishing Ring and Offset Blocks. They are anod- ized aluminum and are susceptible to damage.
  • Page 4 Fire Features You will need to remove ALL of the rocks from your HEMI firepit. Keep the Leave no debris on any river rocks separate from the lava rocks. part of the burner plate. This will make it easier to re-assemble later.
  • Page 5 Fire Features The next step is fishing the pump cord through the 1” hole you just drilled and out the bottom of the bowl. Place the Water Tank on the ground close to the HEMI firepit. Lift up the Burner Plate and feed the cord through the hole you just drilled and then down through a hole in the Fish the cut end of the...
  • Page 6 Fire Features Grab the Water Tank by the Reflector Plate Supports and move it into the As you place in the water firepit. You will need to align the Water- tank, align the cable proof Gland with the 1” hole you just fitting to fit into the 1”...
  • Page 7 Fire Features Attach the Plug to the Pump electrical cord by removing the screws on the Feed pump cord bottom of the plug. through Plug Housing Fish cable through housing and attach and attach leads appro- appropriate wires to terminals. priately.

  • Page 8: Water Level

    Fire Features Go back to the firepit and check to see if your electrical hook-up is working. Check that the pump is Push the ON button on the remote working before filling control and you should hear the pump with water! start up.
  • Page 9 Fire Features The pump is attached to a flexible hose that has adjustable nozzles. The nozzles Adjust water nozzles if can only move up or down. You may more water disturbance need (or want) to adjust how much is desired. water disturbance you will see on top of the reflector plate.
  • Page 10 Fire Features You can now place the Reflector Plate into position. Pick up the plate from the Place Reflector Plate Grab from inside inside edge. onto the supports. with finger tips. BE CAREFUL OF SHARP EDGES and Grab and move plate lower the plate onto the Reflector Plate Supports.
  • Page 11 Fire Features You will only need a small portion of the lava that you original had. Use a Use a small container to small container (like a yoghurt con- slowly fill with lava rock. tainer) and carefully fill up the chamber with lava rock.
  • Page 12 Fire Features DONE! Operate the firepit as You can now turn on your main gas you normally would. supply and light up your firepit as you would normally. NOTE: wait 10 minutes for gas to refill the line and make it to the burner unit before lighting.

  • Page 13: Maintenance

    4th If you have any questions or concerns, please give us a call and we will try to help version: 2019.11.14 as best we can. day. Solus Decor Inc. (North America) Solus UK/Europe 1-877-255-3146 44 208 819 149...