Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AKSO pH Max
Summary of Contents for AKSO pH Max
- Page 1 INSTRUCTION MANUAL pH Max PORTABLE PH METER...
-
Page 3: Table Of Contents
CONTENTS 1 - SPECIFICATIONS ........................4 2 - ACCESSORIES .......................... 5 3 - OVERVIEW ..........................6 FRONT VIEW ..........................6 DISPLAY LCD ..........................7 4 – INSTRUCTIONS OF USE ......................8 Adjustment - pH .......................... 8 Measurement - pH ........................9 Adjustment - ORP ........................ -
Page 4: Specifications
1 - SPECIFICATIONS Measurement range: - 2.00 to 16.00 pH Resolution: 0.01 pH Accuracy for meter: ± 0.02 pH Measurement range: -1999 to 1999 mV Resolution: Accuracy: ± 3 mV Temperature Measurement range: 0 to 80 °C Resolution: 0.1°C Accuracy: ±... -
Page 5: Accessories
Calibration solution pH 10.01 250mL – AK4510 ORP electrode BNC connector PO50 – AK1010 Rubber protective cover – AK1060 Power supply 220VAC/12VDC – AK1075 pH Max Lab – AK110 pH Max Food – AK111 pH Max Meat – AK112 AK1001... -
Page 6: Overview
3 - OVERVIEW FRONT VIEW pH Max: 1 – RCA connector (temperature) 2 – BNC connector (pH) 3 – Display 4 – Mode button 5 – Down button 6 – Hold/Enter button 7 – Cal/Esc button 8 – Up button... -
Page 7: Display Lcd
3 - OVERVIEW DISPLAY LCD pH Max: 1 - Active automatic shutdown 2 - Active adjustment/calibration mode 3 - Slope display indication 4 - Active reading freeze 5 - Inactive 6 - Battery replacement required 7 - ORP measurement unit... -
Page 8: Instructions Of Use
4 – INSTRUCTIONS OF USE POWER ON – POWER OFF To turn the instrument on or off, press the button Adjustment - pH Adjust the instrument’s pH measurement upon receiving it and at least once a week. For greater precision, always do this before using the instrument. The instrument can be adjusted to 1, 2 or 3 pH points, respecting the following sequence combinations: pH7 ... -
Page 9: Measurement - Ph
4 – INSTRUCTIONS OF USE NOTE: Always begin the adjustment at the pH 7.00 point and, after completing the procedure, discard the used portions of the solutions; When saving the adjustment at point pH 4.01 or pH 10.01, the display will show the electrode slope percentage. -
Page 10: Adjustment - Orp
4 – INSTRUCTIONS OF USE Adjustment - ORP The ORP electrode does not require adjustment. However, you can check the electrode’s performance and the accuracy of the readings using an ORP standard solution. Measurement - ORP 1) Connect the ORP electrode to the instrument; 2) Remove the KCl bottle from the electrode tip;... -
Page 11: Additional Functions
5 – ADDITIONAL FUNCTIONS DISPLAY LIGHTING To activate/deactivate the display lighting: 1) In measurement mode, press and hold the button to enter the setup mode. The display will show the indication P01; 2) Using the buttons navigate to the parameter P05 bL and briefly press the button to access it;... -
Page 12: Settings
6 - SETTINGS SETUP MODE To access the instrument’s configurable parameter menu, in measurement mode, press and hold the button . The display will show the indication P01; To navigate between parameters, use the buttons To access a parameter, press the button ... -
Page 13: P05 Bl - Enable/Disable Backlight
6 - SETTINGS P05 bL – Enable/disable backlight On (enable) OFF (disable) P06 CLr – Inactive P07 APO – Enable/disable auto power off On (enable) OFF (disable) P08 rSt – Restore factory settings YES (perform the reset) The figure below shows how the options for the accessed parameter are displayed: 1- Defined Option 2- Another Available... -
Page 14: Maintenance
When the display shows the indication , replace the battery as follows: 1) On the lower rear part of the pH Max, use a suitable screwdriver to remove the four screws that secure the compartment cover as illustrated in the image:... - Page 15 For more information about disposal services and locations, contact your local municipal office. Akso guarantees its instruments against manufacturing defects with the following coverage: 2 wears for bench meters, portable and pocket testers and 6 months for electrodes/sensors (unless otherwise indicated).
Need help?
Do you have a question about the pH Max and is the answer not in the manual?
Questions and answers