Page 1
Type II RO Water Purification System LTWP-A14 www.labtron.com | info@labtron.com...
Page 2
Type II RO Water Purification System LTWP-A14 Index Sr.no Title Page no Safety Measures Introduction Features Specifications Applications Instrument Introduction Installation Operations Replacement...
Page 3
Type II RO Water Purification System LTWP-A14 1. Safety Measures This manual is designed to assist users in properly using and maintaining the equipment to ensure it remains in optimal working condition and prolongs its service life. Kindly read the instructions carefully before using the equipment, approaching it with a scientific attitude.
Page 4
Type II RO Water Purification System LTWP-A14 2. Introduction Type II RO Water Purification System LTWP-A14 is a 80 L capacited modular design which meets the needs of basic laboratory water purifier. It provides Type II level water with consistency and reliability with a TOC level of < 20 ppb. Remove approximately 98% of inorganic ions and 99% of all dissolved organic substances.This...
Type II RO Water Purification System LTWP-A14 4. Specifications Model No. LTWP-A14 Output of Pure water ≥ 50 L / hr. Process Single Pass RO system Water Type Type II Water Tank capacity 80 L Configuration Floor Standing Output of Ultrapure water ≥...
Type II RO Water Purification System LTWP-A14 7. Installation Working Conditions of Water Purification System 1) Voltage: AC220V/50Hz, with reliable ground connection 2) Max power: 100W 3) Tap water temperature: 5-40℃, TDS: 200ppm 4) Tap water pressure: 0.15-0.3Mpa (if above 0.3 Mpa, Then the user needs to take decompression measures.
Page 8
Type II RO Water Purification System LTWP-A14 7.2.1 Installation steps Open the package and confirm the goods as shown in Figure 3, Figure 4 and Figure 5. Figure-3 Host (frame) Figure-4 Pure water tank Figure-5 1/4” Kit...
Page 9
Type II RO Water Purification System LTWP-A14 7.2.2 Installation and operation method 1) Open the tee joint, connect one end to the tap water pipe, and connect the other end to the original tap water outlet or block it with an end cap.
Page 10
Type II RO Water Purification System LTWP-A14 Figure-8 6) Kindly contact the signal wire (above the pure water tank), to the signal socket (rear of the main case) Figure-9 7) After installation, the machine and the site shall be clean and tidy.
Page 11
Type II RO Water Purification System LTWP-A14 8. Operations The operation panel of the machine Figure-10 8.2 Standard procedure for operation maintenance of the machine 8.2.1 Functional specifications of buttons 1) Start: Start/Stop the machine. 2) RO FLUSH/SELECT: Manual RO membrane flush can be started and stopped manually.
Page 12
Type II RO Water Purification System LTWP-A14 At setting the status, the following buttons can be reused: Name of buttons Functions Notes In standby mode, press the button for 3 seconds to PUREWATER/SET enter the Set After choosing the pressure control mode on the circuit board, select the high and low-pressure control points, High-Hxx, L-Lxx.
Page 13
Type II RO Water Purification System LTWP-A14 Manual recycling Timing intake ultrapure water Flicker and display the remaining time Ultrapure Random intake for ultrapure water...
Page 14
Type II RO Water Purification System LTWP-A14 9. Replacement Consumables Replacement Procedure Turn off the water inlet valve first and turn off the power when the low-pressure switch alarm is triggered, which can reduce the residual water in the filter and make it convenient to replace the consumables.
Page 15
Type II RO Water Purification System LTWP-A14 Figure-11 Figure-12...
Page 16
Type II RO Water Purification System LTWP-A14 Replacement and judging method of consumables Replacement Items Quantity Judgment Method Period Replace when the colour of the filter 5μmPP filter 1 piece 2-3 Monthly cartridge becomes deep yellow. If the tap water bleaching powder is...
Need help?
Do you have a question about the LTWP-A14 and is the answer not in the manual?
Questions and answers