Related Manuals for Teleste TEN-FMD1
Summary of Contents for Teleste TEN-FMD1
- Page 1 FTTx SOLUTIONS TEN-FMD1 - Customer Drop Enclosure Installation Guide Rev. 1.00/04.2025...
-
Page 2: Table Of Contents
FTTx Solutions Contents Getting Started............................1 Introduction ............................1 Package Contents ..........................1 About the TEN-FMD1 Customer Drop Enclosure ................. 2 Product Specification - General ......................2 Ordering Information ........................... 2 Mechanical Layout ..........................3 Installation Instructions .........................4 General Preparations and Precautions .................... -
Page 3: Getting Started
This guide will walk you through all the steps for a successful installation. Package Contents Kindly unpack the TEN-FMD1 and confirm that all items are present, as illustrated in Figure 1. Should any items be missing, please promptly contact your local seller for assistance. -
Page 4: About The Ten-Fmd1 Customer Drop Enclosure
FTTx Solutions About the TEN-FMD1 Customer Drop Enclosure The TEN-FMD1 Customer Drop Enclosure is easy to install and operate, featuring a unique IP68 design for superior protection against dust and water, ensuring reliable performance in harsh environments •... -
Page 5: Mechanical Layout
TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions Mechanical Layout Figure 3 - Mechanical layout FTTx - Passives - Customer Drop Enclosure Series... -
Page 6: Installation Instructions
TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions Installation Thank you for choosing this Teleste product. Please take a moment and carefully read these instructions through before installing the product. Instructions General Preparations and Precautions 1. - Page 7 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 2. Remove the tray cassette and Install a tray with an adapter module onto the cassette. All necessary safety instructions must be followed during the installation and maintenance operations.
- Page 8 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 4. Secure the incoming cable with two cable ties to prevent movement and strain. Note! Properly securing the cable is crucial to maintaining the integrity of the optical fibers.
- Page 9 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 7. Secure the tube with a cable tie. Continue routing the incoming fibers around the fiber guides, adjusting the length as needed. Picture 6 8.
- Page 10 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 9. Preparation of the incoming cable is now complete. Note! Always clean optical adapt- ers and connector end faces as part of the enclosure installation; this is crucial for maintaining optimal network performance.
- Page 11 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 11. Insert the cable, anchor the cable’s strength member, and tighten the screw. Picture 10 12. Strip the fiber cable according to the manufacturer’s instructions,...
- Page 12 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 13. The assembly is secured and placed at tray entrance. Picture 12 14. Continue handling the remaining fiber tubes in the same manner Picture 13...
- Page 13 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 15. Make sure the cassette has been turned over. Start installing pigtails into the adapter module, ensuring that each connector end face has been properly cleaned.
- Page 14 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 17. Prepare plastic tubes and carefully organize the pigtails Picture 16 18. Place the assembly at the tray entrance and secure it with a tie.
- Page 15 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 19. Carefully organize the pigtails and route the assembly toward the edge of the cassette. Picture 18 20. Turn the cassette over. Picture 19...
- Page 16 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 21. After turning the cassette over, arrange the assembly at the tray entrance. Picture 20 22. Then, gently secure it with a cable tie.
- Page 17 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 23. Continue organizing the pigtails around the guides and adjust the length as needed. Picture 22 24. Next, prepare for splicing. Proceed with splicing the appropriate fibers for your project.
- Page 18 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 25. Next, it’s time to reassemble the TEN-FMD1 and finish the installation. Picture 24 26. Insert the cassette into the enclosure, ensuring the adapter module is facing upwards.
- Page 19 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 27. Fit the other half of the grommet into its designated track. Picture 26 28. Continue fitting the grommet for the outgoing cable. Picture 27...
- Page 20 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 29. Proceed by installing the grommet(s) designed to support customer drop cables. Picture 28 30. Then, connect the drop cables. Warning! Never look directly into the end of a fiber or a fiber connec- tor that may be carrying laser light.
- Page 21 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 31. Fit the second half of the drop cable grommet. Picture 30 32. Installation of grommets and cables is now complete Picture 31 FTTx - Passives - Customer Drop Enclosure Series...
- Page 22 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions 33. Put the lid back on Picture 32 34. Close the latches and finish by tightening the lid fasteners. Picture 33 FTTx - Passives - Customer Drop Enclosure Series...
- Page 23 TEN-FMD1 Installation Guide Rev. 1.00/04.2025 e n l i g h t e n FTTx Solutions Picture 34 35. This finishes the installation – good work! FTTx - Passives - Customer Drop Enclosure Series...
-
Page 24: Legal Declarations
This document is protected by copyright laws. Unauthorized distribution or reproduction of this document is strictly prohibited. Teleste reserves the right to make changes to any of the products described in this document without notice and all specifications are subject to change without notice. - Page 25 Teleste reserves the right to make changes to any features and specifications of the products without prior notice. Although the information in this document has been reproduced in good faith, the contents of this document are provided “as is”. Teleste makes no warranties of any kind in relation to the accuracy, reliability or contents...
Need help?
Do you have a question about the TEN-FMD1 and is the answer not in the manual?
Questions and answers