Advertisement
Quick Links
ITEM NO.
PART NUMBER
1
GMDM100A
2
GMDM100B
STARLINK MINI ( NOT INCLUDED IN
3
--
HORIZONTAL ENTRY CABLE SEAL
4
CG2090W
5
GMDM100C
6
5161834FHCS
7
516SSW
8
516LOCKWSH
Notes:
1.
Please note that some dimensions may not be
shown (applies to all pages)
2.
Do not scale drawing (applies to all pages)
APXMDM
*Portions of this instruction manual may have been
refined using artificial intelligence to enhance clarity and
readability*
1
DESCRIPTION
QTY.
TALL END CAP
SHORT END CAP
KIT )
( INCLUDED; NOT SHOWN )
MOUNTING PLATE
5/16"-18 X 0.75" CS SCREW
SS WASHER FOR 5/16" BOLTS
SPLIT LOCK WASHER FOR 5/16"
BOLTS
DETAIL A
1
1
1
1
2
8
4
2
4
6
8
7
5
3
A
1
For help e-mail
info@seaviewglobal.com
ph. 1-800-655-7922
Advertisement
Related Manuals for Apex Digital APXMDM
Summary of Contents for Apex Digital APXMDM
- Page 1 BOLTS Notes: Please note that some dimensions may not be shown (applies to all pages) Do not scale drawing (applies to all pages) APXMDM For help e-mail info@seaviewglobal.com ph. 1-800-655-7922 *Portions of this instruction manual may have been refined using artificial intelligence to enhance clarity and...
- Page 2 STARLINK MINI FWD AND AFT CABLE 10.82in ROUTING SLOTS CHECK SPACING 13.13in 11.88in WHEN INSTALLING 12.25in 13.75in CG2090W INCLUDED (CAN 2.8deg MOUNT UNDER ANTENNA OR USING CABLE ROUTING SLOTS AS SHOWN HERE) 2.88in 2.38in APXMDM For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
- Page 3 INSTALLATION INSTRUCTIONS BEGIN ON NEXT PAGE For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
- Page 4 Attach one mounting plate (item from BOM on page 1) to each end cap using the provided countersunk screws (item 6 ). For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
- Page 5 Determine desired mounting location. Use dimensions provided on page 2 to help with this process. Use one of the mounting plates, with the short end cap attached from previous step, to mark and drill holes. It is recommended that the angled surface of the short end cap faces forward.
- Page 6 Using stainless flat and lock washers (item & bolt the short end cap down using nyloc nuts (or similar). Due to varying mounting surface types and thicknesses, ensure the correct mounting bolts and hardware are used. 5/16"-18 hex head bolts are recommended (length will vary).
- Page 7 If mounting cable seal underneath antenna, mark and drill cable seal holes, then route cable through seal using the following instructions: click here. Please note that the antenna is hidden in the view below. Cable For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
- Page 8 After mounting the cable seal in the desired location, slide the antenna into the forward-facing end cap, ensuring the antenna wire exit faces forward. Fully insert the antenna and remove the kickstand. Insert the aft-facing tall end cap into the antenna end as far as possible, then mark and drill holes.
- Page 9 For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
Need help?
Do you have a question about the APXMDM and is the answer not in the manual?
Questions and answers