Apex Digital UA-PRO110 Instruction Manual

BY
INSTRUCTION MANUAL
SPECIFICATIONS
Display Size: 17" - 42"
Maximum Load: 20 kg (44 lbs)
Mounting Pattern: 100 mm x 100 mm, 200 mm x 100 mm, 200
mm x 200 mm
Tilt Range: 5° up to 15° down
Pan/Swivel Range: up to 180°
Pro le: 5.5 cm - 36.2 cm (2.2" - 14.3")
BOX CONTENTS
Mount (x1) Instruction Manual (x1)
Plastic Cover (x2) Hardware Kit (x1)
WARNINGS
Read these instructions before you begin. If you are unsure
1
of any part of the process, contact a professional contractor or
installer for assistance. Improper installation can result in injury
or damage.
2 The wall or mounting surface must be capable of supporting
the combined weight of the mount and the display; if not, the
structure must be reinforced.
3 Locate pipes, wires, or any other hazards in the wall where you
wish to install the mount before drilling.
4 Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
5 Two people are recommended for installation. Do not attempt
to lift a heavy display without assistance.
6
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting your
display. Consult the owner's manual for your particular display
for more information.
CAUTION: This wall mount is intended for use only with the
maximum weight of 20 kg (44 lbs). Use with heavier than the
maximum weights indicated may result in instability causing
possible injury.
TOOLS REQUIRED
Phillips Head Screw Driver
Electric or Portable Drill
3 mm (1/8") Drill Bit and Stud Finder for Drywall Installation
8 mm (5/16") Masonry Bit for Concrete Installation
Level
HARDWARE KIT
(A) Drywall Screw (x2) (H) M6 x 15 Screw (x4)
(B) Washer (x2) (I) M8 x 15 Screw (x4)
(C) Concrete Anchor (x2) (J) M8 x 30 Screw (x4)
(D) M4 x 15 Screw (x4) (K) M8 x 50 Screw (x4)
(E) M4 x 50 Screw (x4) (L) M8 Washer (x4)
(F) M5 x 15 Screw (x4) (M) Spacer (x4)
(G) M5 Washer (x4) (N) S4 Allen Key (x1)
PREPARATION
Prepare the mount for installation
by disassembling the display plate
from the mount. Do this by
removing the safety screws as
shown (see Fig.1). Place the screws
in a safe location.
INSTALLATION
Part 1A – Mounting to the Wall (Drywall)
IMPORTANT! For safety reasons, this mount must be secured
to a wood stud capable of supporting the combined weight of
the mount and display. Do not mount to drywall alone.
Part 1A – Mounting to the Wall (Drywall) (continued)
1 Use a high quality stud finder to locate a stud where you wish
to install your mount. Mark both edges of the stud to help
identify the exact center.
NOTE: You must use the center of the stud to avoid cracking
or splitting the wood during installation.
2 Place the mount against the wall over the marked stud. Make
sure it is level and right side up.
3 Mark two locations (one top and one bottom) at the center of
the stud for securing the mount to the wall (see Fig. 2) and set
it aside.
4 Drill a 3 mm (1/8") pilot hole at each marked location.
5 Place the mount back against the wall and attach it using the
drywall screws (A) and two of the washers (B) provided (see
Fig. 3). Do not over-tighten these screws. Ensure that the
mount remains level after both screws are secured.
Fig. 2
Part 1B – Mounting to the Wall (Concrete)
IMPORTANT! For safety reasons, the concrete wall must be
capable of supporting the combined weight of the mount and
Fig. 1
the display. The manufacturer takes no responsibility for failure
caused by walls of insufficient strength.
1 Place the mount against the wall in
the desired location. Make sure it is
level and right side up.
2 Mark two locations (one top and
one bottom) for securing the mount
to the wall (see Fig. 4) and set it
aside.
3 Drill an 8 mm (5/16") hole at each
marked location. Remove any excess dust from the holes.
Insert a concrete anchor (C) into each hole so that it is flush
4
with the concrete surface (see Fig.5). A hammer can be used
to lightly tap the anchors into place if necessary.
Fig. 3
Fig. 4