Download Print this page

Advertisement

Quick Links

ITEM NO.
PART NUMBER
1
SRM100AM
2
SRM100BM
3
--
4
CG2090W
5
SRM100DV2
6
5161834FHCS
7
516SSW
8
516LOCKWSH
Notes:
1.
Please note that some dimensions may not be
shown (applies to all pages)
2.
Do not scale drawing (applies to all pages)
APXG3DMV2
*Portions of this instruction manual may have been
refined using artificial intelligence to enhance clarity and
readability*
1
DESCRIPTION
TALL END CAP
SHORT END CAP
STARLINK GEN 3 (NOT INCLUDED IN KIT)
HORIZONTAL ENTRY CABLE SEAL
(INCLUDED; NOT SHOWN)
MOUNTING PLATE
5/16"-18 X 0.75" CS SCREW
SS WASHER FOR 5/16" BOLTS
SPLIT LOCK WASHER FOR 5/16"
BOLTS
2
QTY.
1
1
1
1
2
8
4
DETAIL A
SCALE 1 : 1
4
A
6
8
7
5
3
For help e-mail
info@seaviewglobal.com
ph. 1-800-655-7922
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the APXG3DMV2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Apex Digital APXG3DMV2

  • Page 1 BOLTS Notes: Please note that some dimensions may not be shown (applies to all pages) Do not scale drawing (applies to all pages) APXG3DMV2 For help e-mail info@seaviewglobal.com *Portions of this instruction manual may have been ph. 1-800-655-7922 refined using artificial intelligence to enhance clarity and...
  • Page 2 STARLINK GEN3 22.40in 18.50in 17.25in CHECK SPACING FWD AND AFT CABLE WHEN INSTALLING ROUTING SLOTS 23.93in 25.54in CG2090W INCLUDED (CAN 1.3deg MOUNT UNDER ANTENNA OR USING CABLE ROUTING SLOTS AS SHOWN HERE) 2.50in 3.00in APXG3DMV2 For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
  • Page 3 INSTALLATION INSTRUCTIONS BEGIN ON NEXT PAGE For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
  • Page 4 Attach one mounting plate (item from BOM on page 1) to each end cap using the provided countersunk screws (item 6 ). For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
  • Page 5 Determine desired mounting location. Use dimensions provided on page 2 to help with this process. Use one of the mounting plates, with the short end cap attached from previous step, to mark and drill holes. It is recommended that the angled surface of the short end cap faces forward.
  • Page 6 Using stainless flat and lock washers (item & 8 bolt the short end cap down using nyloc nuts (or similar). Due to varying mounting surface types and thicknesses, ensure the correct mounting bolts and hardware are used. DETAIL B Mounting surface For help e-mail info@seaviewglobal.com ph.
  • Page 7 If mounting cable seal underneath antenna, mark and drill cable seal holes, then route cable through seal using the following instructions: click here. Please note that the antenna is hidden in the view below. Cable For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...
  • Page 8 After mounting the cable seal in the desired location, slide the antenna into the forward-facing end cap, ensuring the antenna wire exit faces forward. Fully insert the antenna and remove the kickstand. Insert the aft-facing tall end cap into the antenna end as far as possible, then mark and drill holes.
  • Page 9 For help e-mail info@seaviewglobal.com ph. 1-800-655-7922...