1. Manuals
  2. Brands
  3. Automatic Solutions Manuals
  4. Gate Opener
  5. ASA600
  6. Manual

Automatic Solutions ASA600 Manual

Hide thumbs

Advertisement

Table of Contents

ASA600 – ID200
ASA600
Motor Voltage – 12 volt
Power Absorbed – 70 watts
Speed – 0,019 metres per second
Maximum Thrust – 1500 N
Protection Level – IP43
Duty Cycle – 90%
Dimensions – 970L x 90W x 185H
Stroke – 60 CM
Maximum Leaf – 5 metres
Maximum Leaf Weight – 250 Kg
Opening Time – 31 Seconds
Look for these. They
are "Tips N Tricks"
Solar information
and connections are
on the last page.
GENERAL
1
ID200
Motor Voltage - 12 / 24 DC
Motor Inputs - Two
Battery Charger – Inbuilt 12/24V
Receiver – Inbuilt or External
Limit Switches –No
Pedestrian Input – Yes (NO)
Start Input - Yes (NO)
Stop Input – Yes (NC)
Photocell Input – Two (NC)
Electric Lock – Yes 12Vdc 1A
Slow Speed Regulator – Yes

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ASA600 and is the answer not in the manual?

Questions and answers

Related Manuals for Automatic Solutions ASA600

Summary of Contents for Automatic Solutions ASA600

  • Page 1 ASA600 – ID200 Look for these. They are "Tips N Tricks" Solar information and connections are on the last page. GENERAL ASA600 ID200 Motor Voltage – 12 volt Motor Voltage - 12 / 24 DC Power Absorbed – 70 watts Motor Inputs - Two Speed –...

  • Page 2: Important- Read This First

    GENERAL ORDER OF INSTALLATION To ensure a good installation of the gear motors ASA600, we suggest the following order of installation: 1 - Open the box and take out gear motor. Inspect the contents and ensure all components are present.

  • Page 3: Install Gate Bracket

    ASA600 GEAR MOTOR INSTALLATION INSTALL POST BRACKET The position of the post bracket “A” is critical to the success of your installation and attention needs to be paid to both its correct height and also its position on the post in respect to the relationship between your gate hinge pivot point and the motor pivot point on the bracket.
  • Page 4 ID200 V2 • TIP – Always install the motor/s and program using safety loops as described below before installing accessories. Accessories should be installed one by one following successfully installing and programming the motors. • TIP – You need to fit three small loops of wire to your safety inputs to make anything work. These need to be removed later if you install safety devices to these input terminals.
  • Page 5 Control unit low voltage For 2 motors ID200 V2 Instructions Manual Rev. 2,0...

  • Page 6: Technical Characteristics

    Important: Read carefully this manual before the installation. This manual is integral part of your product, keep it for reference. Warnings: First of all verify that this product is suitable for the installation. Read carefully technical characteristic before the installation. Installation of this control unit must be properly done by qualified installers, following rules and regulations of installation country.
  • Page 7 Wiring Main functions 230Vac Fuse 24V (1) Just a battery voltage can be connected at once, or 12 or 24V. Transformer 12V (1) Out 12Vdc 250mA Lamp. Elettroserratura Antenna. Antenna's shield. Start input N.O. or Open input N.O. (See menu operative logic “OL”). Start Pedestrian input N.O.

  • Page 8: Inputs Status

    Photostop input N.C. or Detect input N.O. (see advanced menu “5F”). Opening Edge or Limit Switch open for slave motor 1 (see advanced menu “EO”). Closing Edge or Limit Switch close for slave motor 1 (see advanced menu “Ec”). Common. Stop input N.C.

  • Page 9: Simple Setup

    Trimmers setting Slow down speed trimmer regulates the slow down speed. Do not set speed too low (less than 10cm/sec on the wing edge) to avoid that gate stops in very cold conditions. Obstacle sensibility trimmer fine tunes the obstacle detection level learned by the control unit during working times programming.
  • Page 10 Push Board Programming shortly Enter Main menu Push Enter button shortly, on the display will appear OL. With up/down it's possible to select all items in this menu. To exit this menu select EX or push up and down together. After 20 seconds without actions, control unit exits itself from this menu.

  • Page 11: Display Function

    Main menu (Continue) Display Function Choiches Description Default Dearman mode Open motor 1. Close motor 1. Open motor 2. Close motor 2. Exit. Exit Exit from main menu. Board programming Advanced menu Push Enter To enter advanced menu hold down enter button 4 seconds, till on display it appear With 4 seconds up/down it's possible to select all items in this menu.
  • Page 12 Advanced menu (Continue) Display Function Choiches Description Default Radio mode Each radio button is learned separate. The installed can choose ho to learn a code: (C1 Start/Open, C2 Pedestrian/close). Learning a button of a remote, let all the other 3 buttons being learn automatically.
  • Page 13 If you do decide to increase the size of your solar panel it may be necessary to install a simple regulator to protect your battery. Check with Automatic Solutions regarding this. SOLAR PANEL DIRECTION Your solar panel ideally should be mounted at an angle of 35 degrees and facing north (NB: In Australia).
  • Page 14 Solar Panel Connection ID200 MPPT Regulator (Optional, if not assembled connect Panel to battery) 12/24V Solar Panel 12/24V Battery Fuse 10A (slow) + This side...

This manual is also suitable for:

Id200

Table of Contents