Related Manuals for Kohler Jacquard K-99505-TK-1WH
Summary of Contents for Kohler Jacquard K-99505-TK-1WH
- Page 1 Installation and Care Guide Vanity with Toe Kick Français, page ″Français-1″ Español, página ″Español-1″ 1216534-2-D...
-
Page 2: Tools And Materials
finished wall for additional support. Remove any moldings that may inhibit the vanity from being flush against the finished wall. To ease installation, remove drawers from the vanity before beginning. Refer to the section in this guide for proper removal. 1216534-2-D Kohler Co. - Page 3 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. Kohler Co. 1216534-2-D...
- Page 4 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. 1216534-2-D Kohler Co.
- Page 5 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. Kohler Co. 1216534-2-D...
- Page 6 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. 1216534-2-D Kohler Co.
- Page 7 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. Kohler Co. 1216534-2-D...
- Page 8 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. 1216534-2-D Kohler Co.
- Page 9 Remove the screw. Using a pair of side cutters, cut the screw at the appropriate notch. Repeat for all screws. Insert a screw through each hole and align them with the handles. Thread the screws into the handles. Kohler Co. 1216534-2-D...
- Page 10 The floor must be flat and perpendicular to the finished wall. Complete the finished wall. Do not install moldings that may inhibit the vanity from being flush against the finished wall. 1216534-2-D Kohler Co.
- Page 11 Verify the vanity is level and plumb against the wall. If necessary, twist the center adjustment leg to level the bottom of the cabinet. If needed, place shims under the unit. Once the cabinet is level, reattach the toe kick by snapping it into place. Kohler Co. 1216534-2-D...
- Page 12 2x6 backing material or any studs. Secure the vanity to the wall with two 5/16″ lag bolts and washers (not provided). Install optional accessories (shelves, drawers, other) as desired. Refer to the instructions packed with the accessories. 1216534-2-D Kohler Co.
-
Page 13: Adjust The Door
4. Adjust the Door The hinges can be adjusted for proper door functionality and alignment. Refer to the illustration and note the screwdriver location for the desired adjustment. Kohler Co. 1216534-2-D... -
Page 14: Remove The Door
Starting with the top bracket, align the hinge pin with the cup of the bracket. Press the back of the hinge to snap the latch onto the bracket. Repeat for the lower hinge. Open and close the door to ensure proper operation. 1216534-2-D Kohler Co. -
Page 15: Remove/Adjust The Drawer
Rotate the drawer down onto the rails, engaging the latches with the rails. Push the drawer closed to fully engage the latches. To ensure the drawer is properly engaged, lightly lift the front of the drawer. If not engaged, repeat the ″Reinstallation″ procedure. Kohler Co. 1216534-2-D...
Need help?
Do you have a question about the Jacquard K-99505-TK-1WH and is the answer not in the manual?
Questions and answers