Subscribe to Our Youtube Channel
Related Manuals for Lumber Jack TC305
Summary of Contents for Lumber Jack TC305
- Page 1 SAFETY AND OPERATING MANUAL Electric Bench Top Tile Cutter TC305 ORIGINAL INSTRUCTIONS...
-
Page 2: Table Of Contents
CONTENTS Introduction ..............02 Intended Use ..............02 Safety General Instructions ..........02 Technical S p ecificat ions ........05 Assembly ................06 Operation ................. 07 Cleaning And Main ten an ce ........09 Stora g e ............. 09 Trouble Shooting ..........10 Explosive View/Chart .......... -
Page 3: Introduction
Introduction � Congratulations on the purchase of your new device. With it, you have chosen a \:{j/ high-quality product. During production, this equipment has been checked for quality and subjected to a final inspection. The functionality of your equipment is therefore guaranteed fit for use. - Page 4 Use protective equipment. • Use safety glasses with side shields that meet ANSI Z87.1 standards. Use hearing protection that meets ANSI 53.19 standards. • Use face or dust mask if working operations create dust. Do not abuse the cord. Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.
-
Page 5: Further Safety Instructions
WARNING! The use of any accessory or attachment other than one recommended in this instruction manual may present a risk of personal injury. Further Safety Instructions • Connect the device only to a power point with a residual current protective device (RCD) with a measured residual current of not more than 30 mA. -
Page 6: Technical Specifications
Technical Specifications Input Voltage ..........230 V-, 50 Hz Power Consumption ........500W Speed ............5400RPM ° Depth of cut 0 ......... .Max. 25mm Sound pressure level (LpA ) ......84.4 dB(A) Sound power level (LwA) measured ..197.40 dB(A) Cutting wheels outer diameter ....115MM Bore hole ............ -
Page 7: Assembly
Assembly WARNING! Caution! Risk of injury! - Ensure that you have sufficient space in which to work, and that you do not endanger other people. - All covers and protective devices must be assembled properly before commissioning. - Disconnect the mains plug before changing the setting on the device Mounting the cutting wheel 1. -
Page 8: Operation
Operation WARNING! Caution! Risk of injury! • Always disconnect the plug from the main socket before working. • Only use cutting wheel and accessories recommended by the manufa cturer. Using other attachment tools and other accessories can represent a risk of injury for you. •... - Page 9 EXTENSION CORDS Make sure the extension cord is in good condition. When using an extension cord, make sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in the voltage, resulting in loss of power and overheating. Use the table to determine the minimum wire size (A.W.G.) extension cord.
-
Page 10: Cleaning And Main Ten An Ce
Performing a mitre cut 1. Place the work table (4) in position. Fix the work table (4) firmly in place with the two set-up aids. ° ° The work table (4) can be fixed in place at 22.5 and 45 4. -
Page 11: Trouble Shooting
Trouble Shooting Problem Possible cause Solution 1.1 Not connected to power supply 1.1. Connect to power supply 1.2 Power cord or plug is defective 1.2. Check by a specialist 1.3 Other electrical defect to the electrician. 1. Product does product 1.3. - Page 13 Q t y Name Q t y Name Rubber Feet Flat washer <D6*18 Self-tapping screws Knob M6*17 ST3.5*16 Rubber mat of switch Self-taooinq screw ST2.9*13 Switch Ruler seat Self-tapping screws Fence ST2.9*12 Small bridqe suooort Guide clamp of parallel stop Outlet hose Work table Power cord and pluq...
-
Page 14: Declaration Of Conformity
Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: Electric Bench Top Tile Cutter Model: TC305 Complies with the following Directives: Electromagnetic Compatibility Directive - 2014/30/EU Machine Directive - 2006/42/EC Restrictions of the use of Hazardous Substances in Electrical Equipment - 2011-65/EU Waste Electrical and Electronic Equipment - 2012/19/EU Standards &...
Need help?
Do you have a question about the TC305 and is the answer not in the manual?
Questions and answers