Related Manuals for Lumber Jack TC180
Summary of Contents for Lumber Jack TC180
- Page 1 SAFETY AND OPERATING MANUAL WATER COOLED TILE CUTTER TC180 ORIGINAL INSTRUCTIONS TC180...
-
Page 2: Table Of Contents
Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..01 Symbols & Cable Rating Chart ……….…………………………………….………04 Machine Details and Product features……….…………………………….….05 Assembly……………………………………………………………………………………..06 Operation…………………………………………………………………………………….07 Maintenance and Service…………………………………………………………….09 Lumberjack Guarantee…………………………………………………………………10 Declaration of conformity……………………………………………………………12 Parts list……………………………………………………………………………………...13 Parts Diagram………………………………………………………………………………15 TC180... -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. TC180... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. TC180...
- Page 5 Materials containing asbestos may only be worked by specialists. Observe the relevant regulations in your country for the materials to be worked. 7.2. Prevent dust accumulation at the workplace. Dust can easily ignite. TC180...
-
Page 6: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 TC180 TC180... -
Page 7: Machine Details And Product Features
This power tool is designed to cut small to medium size tiles (glazed tiles, ceramic tiles or similar) which can be accommodated on the power tool. It is designed for DIY applications and craft businesses in particular. It should never be used to cut wood or metal. TC180 TC180... -
Page 8: Assembly
All parts must be properly – Fill the trough (3) with water until the pump mounted and all conditions fulfilled that inlet is covered by 10mm. ensure faultless operation. Damaged protective devices and parts must be immediately replaced by an authorised service centre. TC180... -
Page 9: Operation
(5) with handle (9). –Position the tile against the rail fence (6) on the angle stop (5). – Tile set up at 90 degrees – Tile set up at 45 degrees TC180... - Page 10 – Move the machine head (29) slowly and smoothly through the tile with the handle – Turn off the machine once the cut is complete, and allow the blade to come to a rest before removing the tile. TC180...
-
Page 11: Maintenance And Service
– Re mount the safety hood (8) using the three remove the safety hood (8). screws (30). – Place the wrench (31) on the motor shaft, and then using wrench (34) loosen the flange nut in the direction of the rotation of the disc. TC180... -
Page 12: Lumberjack Guarantee
Authorised Dealer, you return the product at your own cost to 1.2.8 The product has been purchased by Lumberjack’s or the supplying you, as the guarantee is not transferable Authorised Dealer’s Premises - from a private sale. TC180... - Page 13 Lumberjack. The claim itself should be made in a letter setting out the date and place of purchase, giving a brief explanation of the problem which has led to the claim. TC180...
-
Page 14: Declaration Of Conformity
TC180... -
Page 15: Parts List
PARTS LIST TC180... - Page 16 PARTS LIST TC180...
-
Page 17: Parts Diagram
PARTS DIAGRAM PART 1 TC180... - Page 18 PARTS DIAGRAM PART 2 TC180...
- Page 19 PARTS DIAGRAM FULL TC180...
Need help?
Do you have a question about the TC180 and is the answer not in the manual?
Questions and answers