1. Manuals
  2. Brands
  3. Torc Manuals
  4. Motorcycle Accessories
  5. T-59 SUNDOWNER
  6. User manual

Torc T-59 SUNDOWNER User Manual

Hide thumbs

Advertisement

Table of Contents

T- 5 9 S U N D O W N E R
U S E R ' S M A N U A L
www.torchelmets.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T-59 SUNDOWNER and is the answer not in the manual?

Questions and answers

Related Manuals for Torc T-59 SUNDOWNER

Summary of Contents for Torc T-59 SUNDOWNER

  • Page 1 T- 5 9 S U N D O W N E R U S E R ’ S M A N U A L www.torchelmets.com...
  • Page 2 U S E R ’ S M A N U A L...

  • Page 3: Table Of Contents

    ENGLISH Introduction Do’s and Don’ts T-59 Sundowner Detail Wearing Your Helmet Care and Cleaning Storage Warranty...

  • Page 4: Introduction #1

    TORC helmet. You should also store this manual in a place where you can reference it if any questions arise. You should not use your new TORC helmet until you have read and fully understand the contents of this manual.
  • Page 5 is transmitted to the head and brain, and permanent injury or death may result. In addition, some head injuries are not caused by impacts. They are caused by other forces, like scrambling an egg just by shaking it. You do not have to destroy the shell to destroy the contents. Helmets cannot prevent this type of injury.

  • Page 6: Sundowner Detail #3

    3. T-59 Sundowner Details Certification: DOT FMVSS 218 1. Internal drop-down visor 2. Rivet 3. Padded chin strap with magnetic quick connect buckle 4. Light weight thermal polymer alloy shell 5. EPS impact absorbent liner 6. Antimicrobial sweat wicking liner 4.
  • Page 7 Fasten the retention system (chin strap) as tight Diagram 2 as possible under your jaw without causing pain. There must be no slack in the strap, and the strap must be tight up against your jaw. Test the retention system (chin strap) Put your hands on the back of the helmet and try to push the helmet off by rotating it forward.
  • Page 8 Magnetic quick connect buckle operation 1. To clasp buckle hold receiver side over post side and magnet will pull together and click. Ensure a secure connection is made before riding. 2. Adjust straps length so that they sit tight under your chin. 3.
  • Page 9 Comfort liner installation 1- Comfort liner front: Center the 2- Comfort linear rear: Grasp plastic plate of the comfort liner the plastic plate of the comfort with the shell and push it into EPS liner, align the three snap with the clip until fits securely.
  • Page 10 2. With the chin strap snug under your chin, grab the helmet in the rear at the base and try to pull the helmet forward on your head. Do the same test except grab the helmet in the front and try to roll the helmet rearward. If the helmet comes off your head, the helmet does not fit right and you should not wear it.

  • Page 11: Care And Cleaning #5

    Use only mild soap and water to clean the interior and exterior of your helmet. Never decorate your helmet with paint, decals, stickers, or tape. Torc helmets should not be painted by anyone other than the manufacturer. Many helmet components can be seriously damaged by chemicals and/ or solvents contained in most paint or by careless handling during the repainting process.

  • Page 12: Storage #6

    6. Storage Torc helmets require little special care. However, it is a good idea to protect your helmet from damage if it is to be stored for a long period of time. Helmets should be stored in a cool, dry place. Exposure to temperatures in excess of 130 degrees F (50C) can cause damage, resulting in a loss of protection.
  • Page 13 THANKS FOR CHOOSING TORC HELMETS!
  • Page 14 CORPORATE OFFICES & DISTRIBUTION CENTER: 957 S.LAWSON ST., CITY OF INDUSTRY, CA 91748 1(626)581-8811 www.TORCHELMETS.com facebook.com/OfficialTORCHelmets/ @torchelmets...

Table of Contents