Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Torc T-28
Summary of Contents for Torc T-28
- Page 1 T- 2 8 U S E R ’ S M A N U A L www.torchelmets.com...
- Page 2 U S E R ’ S M A N U A L...
-
Page 3: Table Of Contents
ENGLISH Introduction Do’s and Don’ts T-28 Detail Wearing Your Helmet Modular and Sun visor operation Comfort liner removal / installation Shield removal / installation Care and Cleaning Storage Warranty... -
Page 4: Introduction #1
TORC helmet. You should also store this manual in a place where you can reference it if any questions arise. You should not use your new TORC helmet until you have read and fully understand the contents of this manual. - Page 5 is transmitted to the head and brain, and permanent injury or death may result. In addition, some head injuries are not caused by impacts. They are caused by other forces, like scrambling an egg just by shaking it. You do not have to destroy the shell to destroy the contents. Helmets cannot prevent this type of injury.
-
Page 6: Detail #3
3. T-28 Details Depending on region of intended sale/use, this helmet meets or exceeds the homologation standard shown on the label located on the back of the helmet. Either DOT FMVSS 218 or ECE 1. Light weight thermal polymer alloy shell. - Page 7 Magnetic quick connect buckle operation 1. To clasp buckle hold receiver side over post side and magnet will pull together and click. Ensure a secure connection is made before riding. 2. Adjust straps length so that they sit tight under your chin. 3.
- Page 8 This section is very important: your helmet must be snug on all areas of your head and must be comfortable. Here are two good tests the helmet must pass: 1. Fasten the chin strap under your chin so it is snug with your mouth closed and uncomfortable to open your mouth.
-
Page 9: Modular And Sun Visor Operation #5
sirens). WARNING! It is the responsibility of each user to determine which helmet model is best suited to his or her needs and preferences. Helmet models that cover less of the head provide less impact protection and may be moresusceptible to helmet ejection, which can result in injury or death. -
Page 10: Comfort Liner Removal / Installation #6
Drop down sun visor operation To lower sun visor, slide actuator forward. To raise, slide actuator to back. * DEPENDING ON YOUR HELMET MANUFACTURE DATE IT MAY HAVE A RED OR BLACK ACTUATOR Comfort liner removal / installation Removing and installing liner and cheek pads Cheek pad alignment slot and Top liner rear snaps Cheek pad installation... -
Page 11: Shield Removal / Installation #7
Use only mild soap and water to clean the interior and exterior of your helmet. Never decorate your helmet with paint, decals, stickers, or tape. Torc helmets should not be painted by anyone other than the manufacturer. Many helmet components can be seriously damaged by chemicals and/ or solvents contained in most paint or by careless handling during the repainting process. -
Page 12: Storage #9
9. Storage Torc helmets require little special care. However, it is a good idea to protect your helmet from damage if it is to be stored for a long period of time. Helmets should be stored in a cool, dry place. Exposure to temperatures in excess of 130 degrees F (50C) can cause damage, resulting in a loss of protection. -
Page 13: Warranty #10
Three Year Limited Warranty Subject to the following, Torc Helmets warrants to the original purchaser of each new T-28 purchased from Torc that the helmet when new is free of defective materials and workmanship. Any claim under this warranty must be made when the defect is first discovered, and in no event more than three years after date of purchase. - Page 14 THANKS FOR CHOOSING TORC HELMETS!
- Page 15 CORPORATE OFFICES & DISTRIBUTION CENTER: 957 S.LAWSON ST., CITY OF INDUSTRY, CA 91748 1(626)581-8811 www.TORCHELMETS.com facebook.com/OfficialTORCHelmets/ @torchelmets...
Need help?
Do you have a question about the T-28 and is the answer not in the manual?
Questions and answers