Advertisement
Technical Support and E-Warranty Certificate www.vevor.com/support
ELECTRIC WHEEL CHAIR
OPERATING INSTRUCTIONS
MODEL: JRWD6010
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VEVOR JRWD6010
Summary of Contents for VEVOR JRWD6010
- Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support ELECTRIC WHEEL CHAIR OPERATING INSTRUCTIONS MODEL: JRWD6010 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
- Page 2 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
- Page 3 Please read the user manual carefully before taking the product into use. This manual contains operations , assembly methods , and simple faults solutions. This manual applies to our model : JRWD6010. This manual contains wheelchair maintenance and self checking methods , please put it in proper place.
-
Page 4: Product Introduction
Product Introduction Product Performance This series of electric wheelchairs are powered by Li-ion battery, driven by DC motor. Users control direction and adjust speed by joystick control. It is suitable for application of low speed, good road condition and small slope. Safety Instructions 1.Main Security Features Classified according to the type of protection electric shock: Internal power. - Page 5 Rating voltage: DC.24V. Have no protective effect on the application of defibrillator discharge section. No signal output or input part. Non-permanently installed equipment. 2.Driving Notice General Driving Cautions Please keep your hands on the armrest to control the wheelchair. Please practice in parks or other safe open places until you can use the wheelchair skillfully.
- Page 6 The electric wheelchair is only for personal use, do not carry people or goods, and do not for a traction purposes. Precautions for Uphill and Downhill Avoid driving on following places: steep hills, tilt places, high steps, channels etc. Avoid driving on steep slopes, the slope range should be less than 9 degrees.
- Page 7 malfunction. Keep Dry Do not put the wheelchair in wet place. If the wheelchair is wet, please dry it immediately. Without our company's confirmation, don't modify the assembly or materials of this wheelchair. In order not to cause imbalance, don't add weight arbitrarily. When someone is sitting on the wheelchair or the clutch is not in manual mode, do not use other vehicles to pull or push the wheelchair.
-
Page 8: Usage And Operation
electric wheelchair. There fore, please avoid strong electromagnetic disturbance, like near mobile phone or microwave. Please refer to attachment for notice and manufacturer's statement. Cut-off voltage of battery is 23V. Electric wheelchair belongs to D class in ISO 7176-2009, a wheelchair with electronic differential steering and manual brake. - Page 9 the seat, fold it (picture 4). Picture 3 Picture 4 Install Controller Insert the controller into armrest tube. Please note to keep the controller horizontal (picture 5). And then lock the screw (picture 6). Picture 5 Picture 6 Install and Replace Battery Dismantle battery Disconnect the battery plug and controller plug (picture 7), and then loosen the screw (picture 8).
- Page 10 Picture 7 Picture 8 Install battery Put battery groove in the back tube (picture 9), loosen the screw (picture 10). Then connect the battery plug with controller plug (picture 11). Picture 9 Picture 10 Picture 11 Footplate The footplate can be pulled up or down (picture 12). Picture 12 - 9 -...
- Page 11 Install and Dismantle Anti-tipper Press the button to install/dismantle the anti-tipper (picture 13-14) Picture 13 Picture 14 Armrest Flip-up One hand press the armrest button, another hand flip up the armrest (picture 15). And press down the armrest to the proper position to fix armrest(picture 16).
- Page 12 When changing wheelchair from manual mode to electric mode, please make sure both left and right switches are in same mode. If not, it may cause rollover. Battery and Charger Charger Requirements The charger is used for battery charging. During electric wheelchair is charging, do not use it.
- Page 13 Type 2 (charge through controller) In order to charge the battery, connect the charger with power supply and controller socket. Do as following instructions to complete charging process: Step 1: Make sure the charger groove is not blocked. Step 2: Make sure the electric wheelchair is power off. Step 3: Make sure the battery and controller are connected.
- Page 14 Do not stop charging until charge process is finished. Repeat using of battery which is not fully charged will shorten the battery life, so the battery should be fully charged as much as possible. When battery is fully charged, the power indicator will turn to green. Do not stop charging before fully charged.
- Page 15 The Usage and Maintenance of Battery Wrong operation of replacing battery may cause danger of explosion. Only the same or recommended type of battery is suitable for replacement. And please make sure the battery poles are correct. Key points for prolong the battery life: charge frequently, to keep battery power full.
- Page 16 To charge immediately. Or The leftmost red The battery power is battery is malfunction LED light is lit extremely inadequate. that not able to charge. Two short beeps, The left motor is poor The left motor is LED lights blink connected or the wire malfunction.
- Page 17 Seven short Joystick doesn’t reset, beeps, LED Joystick is malfunction or the lights blink seven connector is loose. times Eight short Please consult your beeps, LED controller is malfunction. dealer for lights blink eight maintenance. times Nine short Please consult service beeps, LED controller is malfunction.
- Page 18 Press this button, the battery power gauge lights will turn on from left to right. Press again, all the LED lights are off. In some emergency, you can directly turn off power by press power button. Sleep Mode If the joystick has no operation more than 20 minutes, the power turn off automatically, and the system in the sleep mode, system will be woke up from sleep mode by press power button.
- Page 19 When there is only the red or yellow LED light lit, the battery should be charged. And for a long distance driving, the battery should be fully charged. If only the red LED light is lit, the battery power is extremely inadequate, users need to charge battery as soon as possible.
- Page 20 Wheels Check the tires and their wear condition regularly. When the tire tread pattern depth reduce to 1mm, please replace new tire. Battery To make sure that the battery is fully charged frequently. In order to prolong battery life, we strongly recommend users do not to charge until battery run out of power totally.
- Page 21 Before use, please check if following parts are correct: 1.Backrest; 2.Armrest; 3.Controller position; 4.Footrest; A area 5.battery power; 6.Clutch/adjusting lever for conversion between manual mode and electric mode Check the following parts monthly, to avoid original parts loosing or wearing 1.Screws;...
- Page 22 The following fees are not covered Replacement of consumables material such as tire, fuse, plastic parts, glass parts, lubricates etc. Fees for Inspection, adjustment , add oil, cleaning , etc. Fees for regularly check that specified by our factory. Unauthorized modifications Out authorized service centers maintain costs.
- Page 23 placed as labeled indication. Transportation should be avoided moisture and sunlight and away from heat resource. In case of electric parts are damaged due to damp, please avoid storing the wheelchair in rain, outdoor and moisture. Storage condition: Environment temperature -40℃～+55℃; Relative humidity≤80%;...
- Page 24 emissions low-voltage power supply network that supplies buildings used for domestic 61000-3-2 purposes. Voltage fluctuations / flicker emissions Complies 61000-3-3 Recommended separation distances between portable and mobile RF communications equipment and the ELECTRIC WHEELCHAIR The ELECTRIC WHEELCHAIR is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
- Page 25 For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
- Page 26 ± 2 kV for ±2 kV for Electrostatic Mains power quality power power transient / should be that of a supply lines supply lines burst typical commercial or ± 1 kV for ± 1 kV for hospital input/output input/output 61000-4-4 environment.
- Page 27 Power frequency (50/60 Hz) magnetic 30A/m 30A/m field IEC 61000-4-8 NOTE: UT is the a. c. mains voltage prior to application of the test level. Guidance and manufacturer´s declaration – electromagnetic immunity The ELECTRIC WHEELCHAIR is intended for use in the electromagnetic environment specified below.
- Page 28 Recommended separation distance 20 V/m 20V/m Radiated RF 26 MHz to 2.5 61000-4-3 where p is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m).b Field strengths from fixed RF transmitters, as determined by an electromagnetic site...
-
Page 29: Performance Parameters
If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the ELECTRIC WHEELCHAIR. B、Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3V/m Performance Parameters Main technical JRWD6010 data Max loading 136kg Speed 1~6km/h weight... - Page 30 DC 24V 20AH Rear wheel Battery 10 inch Li-ion diameter Max driving Motor (*2pcs) DC 24V 250W 20km distance Obstacle Static 50mm 9° climbing stability Climbing Seat size 17.7/20inch* 6° angle Attention:“*” 1. There are two sizes of seat width for this model, which can be determined by the outer box information;...
- Page 31 Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH...
- Page 32 Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the JRWD6010 and is the answer not in the manual?
Questions and answers
What's the width and length of wheelchair
The VEVOR JRWD6010 wheelchair has a width of 23.23 inches and a length of 36.61 inches.
This answer is automatically generated
What's the width and depth of electric wheelchair
The seat width of the VEVOR JRWD6010 electric wheelchair is 20 inches (508 mm). The depth dimension is not provided.
This answer is automatically generated