Related Manuals for Benchmark JD2008U
Summary of Contents for Benchmark JD2008U
- Page 1 3/8" VARIABLE SPEED DRILL 5 Year Limited Warranty E114847 JD2008U WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS BENCHMARK 7 AMP 3/8” VSR DRILL Rating 120 V, 60 Hz, AC Amperes 7 AMP Chuck speed 0-2500 RPM (no load) Chuck 3/8" Keyless Maximum drilling capacity 1" (25 mm) in wood Maximum drilling capacity 3/8" (10 mm) -
Page 3: Table Of Contents
1240-001 3/8" VARIABLE SPEED DRILL TABLE OF CONTENTS Product Specifications .................. 1 Table of Contents ..................2 General Safety Warnings ................3-6 Specific Safety Rules ..................7 Extension Cord Safety ................... 8 Symbols ......................9 Know your Drill .................... 10 Assembly and Operating ................. -
Page 4: General Safety Warnings
GENERAL SAFETY WARNINGS WARNING: Before using this tool or any of its accessories, read this manual and follow all Safety Rules and Operating Instructions. The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible situations. It must be understood that common sense and caution are factors which cannot be built into the product. -
Page 5: Work Area Safety
1240-001 3/8" VARIABLE SPEED DRILL WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. WORK AREA SAFETY Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. - Page 6 Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Page 7 1240-001 3/8" VARIABLE SPEED DRILL...
-
Page 8: Specific Safety Rules
SPECIFIC SAFETY RULES WARNING: Know your drill. Do not plug the drill into the power source until you have read and understand this Instruction Manual. Learn the tool’s applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury. -
Page 9: Guidelines For Extension Cords
1240-001 3/8" VARIABLE SPEED DRILL GUIDELINES FOR EXTENSION CORDS WARNING: Keep the extension cord clear of the working area. Position the cord so it will not get caught on the workpiece, tools or any other obstructions while you are working with the power tool. Make sure any extension cord used with this tool is in good condition. -
Page 10: Symbols
Directional arrow Seconds Warning symbol or AC Alternating current Wear your safety glasses Three-phase alternating Wear hearing protection current This symbol designates that this tool os listed with U.S. repuirements by MET Laboratories, Inc. UL62841-1，UL62841-2-1; E114847 CSA C22.2#62841-1，CSA C22.2#62841-2-1. JD2008U... -
Page 11: Know Your Drill
1240-001 3/8" VARIABLE SPEED DRILL KNOW YOUR DRILL Belt clip Chuck Air vents Air vents Trigger switch lock-on button Forward/reverse button Variable speed trigger switch... -
Page 12: Assembly And Operating
ASSEMBLY AND OPERATING FORWARD/REVERSE SWITCH The forward/reverse switch (1) is conveniently mounted above the trigger switch (2) (Fig. 1). To make the drill rotate clockwise for drilling, push the forward/reverse switch to the left. To make the drill rotate counter-clockwise, push the forward/ reverse switch to the right. -
Page 13: Installing Drill Bits
1240-001 3/8" VARIABLE SPEED DRILL INSTALLING DRILL BITS WARNING: Never hold the chuck body with one hand and use the drill power to rotate the drill body to loosen or tighten bits. Serious injury may result. This drill is equipped with a keyless chuck. This chuck is designed to provide easy two-handed tightening and loosening of the chuck jaws. -
Page 14: Trigger Switch Lock
TRIGGER SWITCH LOCK The trigger switch lock-on feature allows the trigger switch to be locked in the ON position at full speed when continuous operation for extended periods of time is required (Fig. 5). To lock the trigger switch in the ON position, pull back on the trigger switch to start the drill. - Page 15 1240-001 3/8" VARIABLE SPEED DRILL NOTE: Make sure the hand placed on the body of the drill does not cover the air vents. Covering these air vents will reduce motor cooling, and possibly lead to overheating the motor. 3. While holding the drill firmly, place the point of the drill bit at the point to be drilled.
-
Page 16: Retightening A Loose Chuck
7. Insert the hex key into the chuck and tighten jaws of chuck securely (Fig. 9). Tap the hex key sharply with a mallet in a COUNTER-CLOCKWISE direction. This will loosen the chuck on the spindle. The chuck can now be unscrewed and removed from the spindle by hand. -
Page 17: Maintenance
1240-001 3/8" VARIABLE SPEED DRILL MAINTENANCE GENERAL WARNING: When servicing, use only identical replacement parts. The use of any other part may create a hazard or cause product damage. DO NOT use solvents when cleaning plastic parts. Plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. -
Page 18: Exploded View
EXPLODED VIEW... -
Page 19: Parts List
1240-001 3/8" VARIABLE SPEED DRILL PARTS LIST WARNING When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the drill. Any attempt to repair or replace electrical parts on this drill may create a safety hazard unless repairs are performed by a qualified technician. -
Page 20: Warranty
WARRANTY BENCHMARK 7 AMP 3/8" VSR DRILL If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 21 1240-001 3/8" VARIABLE SPEED DRILL...
- Page 22 3/8" VARIABLE SPEED DRILL 5 Year Limited Warranty 1240-001 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects in workmanship and materials.
Need help?
Do you have a question about the JD2008U and is the answer not in the manual?
Questions and answers