Subscribe to Our Youtube Channel
Related Manuals for Benchmark 1282661
Summary of Contents for Benchmark 1282661
- Page 1 3/8" PNEUMATIC DRILL 5 Year Limited Warranty READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS 3/8" PNEUMATIC DRILL Chuck 3/8" (10mm) keyless Max speed 1,800 RPM (no load) Average air consumption 4 CFM @ 90 PSI Maximum air pressure 120 psi (8.3 bar) Working pressure 90 psi (6.2 bar) Air inlet size 1/4” NPT Recommended hose 3/8”... -
Page 3: Table Of Contents
1282 661 3/8" PNEUMATIC DRILL TABLE OF CONTENTS Product Specifications ................... 1 Table of Contents ................... 2 Safety Guidelines ..................3-6 Symbols ....................... 7 Tool Specific Warnings .................. 8 ..............9 Know Your 3/8" Pneumatic Drill ..............10-16 Assembly and Operation .................. -
Page 4: Safety Guidelines
SAFETY GUIDELINES WARNING: This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. DANGER! Potential hazard that will result in serious injury or loss of life. -
Page 5: Symbols
1282 661 3/8" PNEUMATIC DRILL SYMBOL MEANING • Risk of inhalation: Never directly inhale the air produced by the compressor. • Risk of bursting: Do not adjust the pressure switch or safety valve for any reason. They have been pre-set at the factory for this compressor’s maximum pressure Tampering with the pressure switch or the safety valve may cause personal injury or property damage. - Page 6 WARNING! • Do not allow unskilled or untrained individuals to operate the air tool. • Do not use the tool for any task other than that it is designed to perform. • Locate the compressor in a well-ventilated area for cooling, and a minimum of 12”...
- Page 7 1282 661 3/8" PNEUMATIC DRILL CAUTION! • Disconnect tool from the air supply and turn o the compressor before performing any maintenance or changing accessories, when clearing a jammed fastener, when the tool is not in use, when it is being handed to another person, and when it is left unattended.
-
Page 9: Tool Specific Warnings
1282 661 3/8" PNEUMATIC DRILL TOOL SPECIFIC WARNINGS DANGER Potential hazard that will result in serious injury or death. • Do not disconnect or reconnect the air hose with the tool pressed. WARNING Potential hazard that could result in serious injury or death. •... -
Page 10: Know Your 3/8" Pneumatic Drill
KNOW YOUR 3/8" PNEUMATIC DRILL Keyless 3/8" chuck Forward/Reverse Switch Trigger Handle ¼" Air Inlet Exhaust... -
Page 11: Assembly And Operation
1282 661 3/8" PNEUMATIC DRILL ASSEMBLY AND OPERATION Compatible Compressors Guidelines for proper use and operation Be sure to use proper air compressor with air-powered tools. The compressor should be able to supply a minimal air delivery of 4 CFM @ 90 SPI to ensure the compressor can run continuously with the tool. - Page 12 The inside diameter of the hose should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D. and fittings should have 1/4" NPT thread. The use of air line lubricators and air line filters is recommended to prevent water in the line that can damage the tool.
- Page 13 1282 661 3/8" PNEUMATIC DRILL TRIGGER The trigger (1) allows the operator to control the start and stop of the air tool. (Fig. 3) FORWARD/REVERSE SWITCH The forward/reverse switch (2) is located on the left side of the trigger and the switch is marked F for forward and R for reverse.
- Page 14 WARNING: Read all instructions before using this tool. All operators must be fully trained in its use and aware of these safety rules. Do not exceed the maximum working air pressure of 120 psi/8.3 bar. Use personal safety equipment. Use only compressed air at the recommended conditions. If the tool appears to malfunction, remove from use immediately and arrange for service and repair.
- Page 15 1282 661 3/8" PNEUMATIC DRILL PRE-START CHECKLIST • Drain water from air compressor tank and condensation from air lines. (Please refer to air compressor’s operation manual.) Lubricate the tool. (Please refer to the “Maintenance” section in the manual.) • WARNING: Risk of unsafe operation. Firmly grasp air hose with hand when installing or disconnecting to prevent hose whip.
- Page 16 DRILL BIT CHUCK Fig. 6 NOTE: Whenever possible, secure the working piece in a vise or clamp prior to starting drilling.
- Page 17 1282 661 3/8" PNEUMATIC DRILL OPERATING PROCEDURES START-UP • Turn on the air compressor and allow the air tank to be filled. Set the air compressor regulator to 90 PSI. This air tool operates at a maximum of • 90 PSI air pressure. Adjust tool either in forward or reverse position.
-
Page 18: Maintenance
MAINTENANCE NOTE: Do not store the tool anywhere temperatures will fall below freezing. DANGER! Disconnect the tool from the air compressor before maintenance/ service, adjusting, cleaning jams, reloading, and when it is not in use. Repairs must be performed by a qualified service technician only. Failure to comply will lead to serious injury or loss of life. -
Page 19: Exploded View
1282 661 3/8" PNEUMATIC DRILL EXPLODED VIEW... -
Page 20: Parts List
PARTS LIST WARNING: When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this tool may create a safety hazard unless repairs are performed by a qualified technician. - Page 21 1282 661 3/8" PNEUMATIC DRILL Key # Part # Part Name Quantity 03.02.01.011.020 Washer 03.05.11.051 Chuck 3/8" 03.05.07.244 Chuck Screw 03.05.01.027 O-ring 10.6x1.8...
-
Page 22: Warranty
WARRANTY BENCHMARK WARRANTY If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 23 3/8" PNEUMATIC DRILL *5-year limited warranty on tool 1282 661 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects in workmanship and materials.
Need help?
Do you have a question about the 1282661 and is the answer not in the manual?
Questions and answers