Subscribe to Our Youtube Channel
Related Manuals for Lumber Jack PT254/H
Summary of Contents for Lumber Jack PT254/H
- Page 1 SAFETY AND OPERATING MANUAL 10" PLANER THICKNESSER PT254/H ORIGINAL INSTRUCTIONS PT254/H...
-
Page 2: Table Of Contents
Structure and Functions…………………….6-7 Supplementary Safety Instructions………..7 Operation Regulations………………………8-10 Maintenance…………………………………11 Attention ……………………………………..11 Assembly Diagram and List………………..12-15 SPECIFICATIONS PT254/H Model No Motor 1500W (Please choose proper power source, voltage and frequency that are shown in the label for your machine.) No. of Blade... - Page 3 - Keep work area well lit. - In particular, no inflammable liquids or gases must be present. (3) Guard against electric shock - Avoid body contact with earthed or grounded surface. (4) Keep children and other persons away - Don’t let especially children, persons not involved in the work touch the tool or extension cord and keep them away from the work area.
-
Page 4: Supplementary Safety Instructions
(18) Use outdoor extension leads - When the tool is used outdoors, use only extension cords intended for outdoor use and so marked. (19) Stay alert - Watch what you are doing, use common sense and do not operate the tool when you are tired. (20) Check damaged parts - Before further use of tool, it should be carefully checked to determine that it will operate properly and perform it’s intended function. -
Page 5: User Responsibility
⑽ Never make jointing or planning cut deeper than 2 mm. USER RESPONSIBILITY This machine will perform in conformity with the description contained in this manual when installed, operated, maintained and repaired in accordance with the instructions provided. This machine must be checked periodically. Defective equipment (including power cable) should not be used. -
Page 6: Structure And Functions
Figure2 STRUCTURE AND FUNCTIONS The surface Planer Thicknesser is a transportable electric tool. The machine is driven by a single-phase series motor, and it is double insulated. It is used to Planer Thicknesser wood. It has the characteristics of rational structure, easy operation and high efficiency. Refer to figure 3. Safety Switch 230V Circle Breaker... -
Page 7: Operation Regulations
OPERATION REGULATIONS ATTENTION: Make sure that the switch is in off position before adjusting the cutting depth, replacing or adjusting the blades. Make sure the blade screws are securely tightened. Assemble stand with M6 hex nut, 6mm flat washer and carriage bolt. Then install the machine to the stand and secure it with M8X30 hex bolt and 8mm flat washer OVERLOAD PROTECTION If the motor protection responds, this always indicates that the motor is overloaded. - Page 8 CHIP EXTRACTION To ensure trouble free and reliable operation on enclosed premises, the machine must be connected to an extractor unit at the dust chute E (accessory) DUST CHUTE CONNECTION WHEN PLANING : - Lift up the blade guard arm F so that the longitude holes G being exposed; - Pull out the key H on both sides of the dust chute E;...
- Page 9 Figure 8 SETTING OF GUARD Height adjustment is made with the lever mounted on the left side of the machine. After lifting the lock lever the blade cover can be slide ways to set the required stock width for jointing. Push lock lever down to lock guard extrusion in position.
- Page 10 REPLACING BLADES （FOR STRAIGHT CUTTING BLADE OF MODEL PT254） Ruler Out-feed table In-feed table ⚫ Put the main switch of the machine to OFF position. ⚫ Pull the power supply plug from the socket. ⚫ Pull the cutter block guard aside. ⚫...
-
Page 11: Maintenance
REPLACING/ROTATING KNIFE INSERTS （FOR HELICAL KNIFE INSERTS OF MODEL PT254H） CAUTION: Make sure the switch is in the OFF position and cord is unplugged before proceeding with checking blades. Knife inserts are extremely sharp. Use caution when cleaning or changing. Failure to comply may cause serious injury. -
Page 12: Attention
ATTENTION! Through poor conditions of the electrical MAINS, shortly voltage drops can appear when starting the EQUIPMENT. This can influence other equipment (e.g. Blinking of a lamp). If the MAINS IMPEDANCE max<0.464 OHM, such disturbances are not expected. (In case of need, you may contact your local supply authority for further information). - Page 14 Socket head screw Flat washer Cord hook Lock washer Rear wall plate Socket head screw Socket head screw Hex bar Hex nut Hex nut M14 Foot Socket head screw Base Cable tie Pan head screw Bushing Cord clamp Bushing Hex nut Reset button assembly Lock washer Quick connecting terminal...
- Page 15 128-1 Retaining ring Pan head screw M5X10 128-2 Retaining ring Lock washer 5mm 128-3 Lock washer 8mm Flat washer 5mm Serriated washer 5mm Knob Motor pulley Socket head screw Motor Interlock switch Ball bearing Switch fixing plate 132-1 Flat washer Bearing house 132-2 Socket head screw Flat washer...
- Page 16 Socket head screw Hex nut Dust chute Thread forming screw Dust chute cover Thread forming screw Knob 176-1 Retaining ring Push stick Hex wrench Pan head screw Flat washer Guide block Ball bearing Bearing house Helical cutting head Knife insert Screw Bearing house Ball bearing...
-
Page 17: Declaration Of Conformity
DECLARATION OF CONFORMITY We Importer: TOOLSA VE LTD Unit C, Manders Ind. Est., Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: 1500W Planer Thicknesser Model: PT254/PT254H Complies with the following Directives: Electromagnetic Compatibility Directive - 2004/108/EC Machine Directive - 2006/42/EC Restrictions of the use of Hazardous Substances in Electrical Equipment - 2011-65/EU Waste Electrical and Electronic Equipment - 2012/19/EU...
Need help?
Do you have a question about the PT254/H and is the answer not in the manual?
Questions and answers