Subscribe to Our Youtube Channel
Related Manuals for Lumber Jack PT1000
Summary of Contents for Lumber Jack PT1000
- Page 1 SAFETY AND OPERATING MANUAL PLANER THICKNESSER 230v PT1000 ORIGINAL INSTRUCTIONS PT1000...
-
Page 2: Table Of Contents
Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..01 Symbols & Cable Rating Chart ……….…………………………………….………04 Machine Details and Product features……….…………………………….….05 Assembly……………………………………………………………………………………..06 Operation…………………………………………………………………………………….09 Maintenance and Service……………………………..…..…………………………12 Lumberjack Guarantee…………………………………………………………………15 Declaration of Conformity………….………………………………………………..17 Parts List & Diagram………………………………………………………….…………18 Parts Diagram………………………………………………………………….…………..22 PT1000... -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. PT1000... - Page 4 Power tools are cancer. Materials containing asbestos may only be dangerous in the hands of untrained users. worked by specialists. Observe the relevant regulations in your country for the materials to be worked. PT1000...
- Page 5 8.7 When working, always hold the planer in such a manner that the planer base plate faces flat on the work piece. Otherwise the planer can become wedged and lead to injuries. PT1000...
-
Page 6: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 PT1000 PT1000... -
Page 7: Machine Details And Product Features
Package Contents: fitted. It is not intended for continuous production or production line use. Planer – Jointer Stand Dust Flume Push Blocks PT1000 PT1000... -
Page 8: Assembly
(EE). Attach the other end of the stand top – Place the stand upright. Ensure that the stand is on support (H) to the second leg in the same a level surface and all four legs are contacting the manner. surface. Hand‐tighten only at this time. PT1000... - Page 9 Attach planer table lock handle (U) and flat washer (T). Cutter head Guard – Install cutter head guard (C) by securing the bracket (C1) to the side of the jointer infeed table (F5) with two each pan head machine screws (FF) and hex nuts (GG). PT1000...
- Page 10 (F1). – Raise the table (turn handle (S) clockwise) until the dust chute (B) is held firmly in place between the planer infeed table (F1) and jointer outfeed table (F2). Do not over tighten. PT1000...
-
Page 11: Operation
The left hand is transferred to the out feed side and presses down on this part of the workpiece, at the same time maintaining flat contact with the fence. PT1000... - Page 12 Several passes may be required to achieve full bevel. stop for the hands in the event of a kickback. CAUTION! When workpiece is twice the length of the jointer infeed or outfeed table use an infeed or outfeed support. PT1000...
- Page 13 – When planing hardwood, take light cuts or plane the wood in thin widths. – Make a test cut with a test piece and verify the thickness produced. – Check the accuracy of the test cut before working on the finished product. PT1000...
-
Page 14: Maintenance And Service
Use extreme caution when inspecting, removing, sharpening or replacing knives into the cutter head. Failure to comply may cause serious injury! Determining if adjustment is necessary: – Disconnect machine from the power source. – Remove the cutter head guard. PT1000... - Page 15 Failure to comply may cause serious adjustment is required as follows: injury. Adjustment procedure – Slightly loosen seven gib lock screws (A) by turning into the lock bar (B), clockwise as viewed from the infeed table (K). PT1000...
- Page 16 – When gum and pitch collect on the blades, The cutter head ball bearings are lifetime lubricated carefully remove with a strong solvent. Failure tore and need no further care move gum and pitch build up may result in excessive friction, blade wear and overheating. PT1000...
-
Page 17: Lumberjack Guarantee
Authorised Dealer, you return the product at your own cost to 1.2.8 The product has been purchased by Lumberjack’s or the supplying you, as the guarantee is not transferable Authorised Dealer’s Premises - from a private sale. PT1000... - Page 18 Lumberjack. The claim itself should be made in a letter setting out the date and place of purchase, giving a brief explanation of the problem which has led to the claim. PT1000 PT1000...
-
Page 19: Declaration Of Conformity
PT1000... -
Page 20: Parts List & Diagram
PARTS LIST PT1000... - Page 21 PARTS LIST PT1000...
- Page 22 PARTS LIST PT1000...
- Page 23 PARTS LIST PT1000 PT1000...
-
Page 24: Parts Diagram 1
PARTS DIAGRAM 1 PT1000... - Page 25 PARTS DIAGRAM 2 PT1000...
- Page 26 PARTS DIAGRAM FULL PT1000...
Need help?
Do you have a question about the PT1000 and is the answer not in the manual?
Questions and answers