Related Manuals for URYU UET-10CU
Summary of Contents for URYU UET-10CU
- Page 1 Digital Torque Tester UET-10CU Instruction Manual Version 1.2 November 2020 URYU SEISAKU, LTD.
-
Page 2: Table Of Contents
Table of contents Safety cautions ............................. 2 Outline ..............................5 2.1. Features ............................5 2.2. Installation place ........................... 6 2.3. Environmental condition ........................ 6 Appearance, parts names and functions ..................... 7 3.1. Standard accessories ........................8 3.2. Specifications ..........................9 How to use ............................ -
Page 3: Safety Cautions
1. Safety cautions Read through this instruction manual before installation, operation, maintenance and inspection for proper use of UET-10CU. Use UET-10CU only after you master knowledge, safety information and all safety cautions. Keep this instruction manual at the place where users can read any time. -
Page 4: Operation And Use
Cover your long hair with a rubber band or a cap to avoid covering UET-10CU with your hair causing injuries. ●Avoid physical injury caused by UET-10CU in the event of an earthquake by fixing and installing firmly. -
Page 5: General Warning
Take off metalware like watches or rings before operation. ●Only URYU SEISAKU, LTD or its approved companies overhauls UET-10CU. There is a risk of shock, injury and fire. ●Use only dedicated charger and battery. There is a risk of damage or injury due to breakage. -
Page 6: Outline
Outline UET-10CU is a torque tester dedicated to stall type tools. With the built-in torque sensor, UET-10CU is made to work out torque measurement and display of our US-LT torque control drivers and US-LD direct drivers etc. UET-10CU is also ideal for small hand torque wrenches’ periodic check. -
Page 7: Installation Place
･･･The above categorization is of the over voltage category (Ⅰ, Ⅱ, Ⅲ), and contamination level (1, 2, ※ 3) as per IEC664. UET-10CU has been categorized as the over voltage category Ⅲ and the contamination degree 3. Note: IEC is International Electric Standard Committee. -
Page 8: Appearance, Parts Names And Functions
Type (Kg) UET- 10CU ①Power switch ・・・Press this button, and UET-10CU is powered on (STANDBY/ON). ②Charge jack ・・・Use only dedicated charger. ③LED (green) ・・・This LED lights during charge and goes out following the completion. ・・・Insert accessory attachment to secure the torque measuring object. -
Page 9: Standard Accessories
3.1. Standard accessories 946-928-0 Hexagon Head Bolt (M8X20) HARD JOINT 910-907-0 Battery Charger for UET-10CUA 910-908-0 Battery Charger for UET-10CUE 8 pcs. 962-601-0 Belleville Spring (25X12.2X1.5) STRONG 918-129-0 Hexagon Socket Bit (13X100) (5H) 918-223-0 Hexagon Socket Bit (13X100) (6.35H) 836-890-4 Driver Attachment Assembly SOFT JOINT (consisting of the below) 946-930-0 Hexagon Head Bolt (M8X35) 836-397-3 San Blade Holder Flange... -
Page 10: Specifications
RS232C (Baud rate 19200 bps) Built-in battery ・Use only dedicated charger (AC adapter). Power ・Do not use UET-10CU for torque measurement during battery charge. ・Keep battery separate from UET-10CU if it remains unused for a long time. Charger Input power AC100~240V 50/60Hz... -
Page 11: How To Use
※Never apply torque greater than 10Nm to UET-10CU. ⑥Press RESET button to clear torque value on DPM. ※ Press RESET button only after UET-10CU has output torque data from RS232C. If RESET button is pressed before data output, UET-10CU will output cleared data 0.0Nm. -
Page 12: Rs232C
Battery in use Model name: Battery Ni-MH(10CU)5HR-AAUC Part code: 910-906-0 Recycle or dispose of used battery as stipulated by local regulation. 6. Cleaning Wipe UET-10CU with a piece of soft cloth wet by water or a small amount of neutral detergent. - Page 13 After-sales services Feel free to inquire at the below parties Distributed by:...
Need help?
Do you have a question about the UET-10CU and is the answer not in the manual?
Questions and answers