1. Manuals
  2. Brands
  3. Event Lighting Manuals
  4. Controller
  5. APRO4
  6. User manual

Event Lighting APRO4 User Manual

Hide thumbs

Advertisement

Table of Contents

www.event-lighting.com.au
APRO4
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0 (August 2024)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the APRO4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Event Lighting APRO4

Summary of Contents for Event Lighting APRO4

  • Page 1 For your safety, please read this user manual carefully before use. Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions.

  • Page 2: Panel Overview

    www.event-lighting.com.au FEATURES DMX 512, RDM, Artnet and sACN support Remote configuration via internal webpage Update firmware on Webpage DMX output isolation RJ45 Ethernet B input with POE（DC12V 2A） 1.7”LCD Display Gigabit network, 100/1000mbps port speed PANEL OVERVIEW...
  • Page 3 www.event-lighting.com.au 1. Fuse T1.25A 250V 2. Power switch 3. Power indicator 4. Device identification indicator: When webpage send a device verification command, this LED will flash 5. Display 6. Rotary Encoder with push button 7. DMX output indicator 8. Network port speed status LED: When connecting to the network, if port speed is set to 100Mbps , the red indicator is on, if transmitting data, the red indicator will be flashing.
  • Page 4 www.event-lighting.com.au DHCP IP Mode Static Static Network IP Address 2.xx.xx.xx 2.xx.xx.xx Subnet Mask 255.0.0.0 255.0.0.0 Input Mode Output Output ArtNet Protocol ArtNet sACN Universe 1 – 32767 20Hz Port 1 25Hz 30Hz Frame Rate 30Hz 35Hz 40Hz Disable Enable Enable Input Mode Output...

  • Page 5: Web Configuration

    Please Note: When you set DMX 1-4 as inputs, then you can only use Artnet as output, but not sACN. DHCP mode When APRO4 is set to DHCP mode, set the computer to DHCP mode also. And use a router for linking computer and APRO4 controller. The display will show IP address like below...

  • Page 6: Static Mode

    Static mode When APRO4 is set to Static mode, set computer to be Static mode also. APRO4 device will show IP address as below(Note: This is just an example of Web IP address, will be different) Then set the IP address of computer is in the same IP range .
  • Page 7 Input IP address of APRO 4 controller by browser, then login to configure the parameter of controller. Enter password: admin When log on Config web, the first page show the information about APRO4...
  • Page 8 www.event-lighting.com.au Following is for Network setting, set IP mode to be Static or DHCP, IP Address,and Subnet Mask. After setting, click Save button . For DMX Port page , it is used for DMX Port setting. Can set each port as input or output.
  • Page 9 On the page of Settings , set Splitter, Signal Loss status, Display timeout and Merge Mode. After setting, click Save to store the setting. Return to Factory setting by clicking Factory Reset button. On Update page, update software of fixture by selecting the update software file of APRO4.
  • Page 10 www.event-lighting.com.au On the last page, reset password.

  • Page 11: Warranty

    SPECIFICATION Power in: AC 100-240V,50/60Hz Power consumption: AC240V , 34mA 4.8W Size:220x182x43.8mm Weight: 1.63Kg POE 802.3af IP20 Warranty Please refer to your local dealer or contact Event Lighting. www.event-lighting.com.au...

Table of Contents