Advertisement
Quick Links
D
Originalbetriebsanleitung
Hand-Rasenmäher
GB
Original operating instructions
Manual lawn mower
F
Instructions d'origine
Tondeuse a gazon manuelle
I
Istruzioni per l'uso originali
Tosaerba manuale
DK/
Original betjeningsvejledning
N
Håndskubbet græsslåmaskine
S
Original-bruksanvisning
Handgräsklippare
NL
Originele handleiding
Handmaaier
E
Manual de instrucciones original
Cortacésped manual
FIN
Alkuperäiskäyttöohje
Käsikäyttöinen ruohonleikkuri
9
Art.-Nr.: 34.141.14
Art.-Nr.: 34.141.29
Anl_GC_HM_400_300_SPK9.indb 1
GC-HM 300
GC-HM 400
I.-Nr.: 21010
I.-Nr.: 21010
14.07.2020 10:42:35
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EINHELL GC-HM 300
Summary of Contents for EINHELL GC-HM 300
- Page 1 GC-HM 300 GC-HM 400 Originalbetriebsanleitung Hand-Rasenmäher Original operating instructions Manual lawn mower Instructions d’origine Tondeuse a gazon manuelle Istruzioni per l’uso originali Tosaerba manuale Original betjeningsvejledning Håndskubbet græsslåmaskine Original-bruksanvisning Handgräsklippare Originele handleiding Handmaaier Manual de instrucciones original Cortacésped manual Alkuperäiskäyttöohje Käsikäyttöinen ruohonleikkuri...
- Page 2 - 2 - Anl_GC_HM_400_300_SPK9.indb 2 14.07.2020 10:42:36...
- Page 3 - 3 - Anl_GC_HM_400_300_SPK9.indb 3 14.07.2020 10:42:37...
- Page 4 - 4 - Anl_GC_HM_400_300_SPK9.indb 4 14.07.2020 10:42:38...
- Page 5 Table of contents 1. Safety regulations 2. Layout and items supplied 3. Proper use 4. Technical data 5. Before starting the equipment 6. Operation 7. Cleaning, maintenance and ordering of spare parts 8. Disposal and recycling 9. Storage and transport 10.
-
Page 6: Safety Regulations
Danger! 16. Bar frame When using the equipment, a few safety pre- 17. Grass box with holding belt cautions must be observed to avoid injuries and 18. Screw M6 x 30 (4x) damage. Please read the complete operating 19. Screw M6 x 25 (4x) instructions and safety regulations with due care. -
Page 7: Operation
4. Technical data Four diff erent cutting heights can be set between a range of 13-37 mm. To do so, pull the spring- GC-HM 300 loaded bolts (A) on both sides of out and then Working width: ..........30 cm engage them in the required holes. -
Page 8: Cleaning, Maintenance And Ordering Of Spare Parts
been switched off . Never attempt to manually 7.2.1 Setting the counter blade (Fig. 9) stop the blade. Regularly check to see if the Warning! Wear safety gloves. blade is securely attached, is in good condition and is sharp. If the contrary is the case, sharpen Note: the blade or replace it. -
Page 9: Disposal And Recycling
At the end of the season, perform a general ins- your household refuse. The equipment should be pection of the lawn mower and remove any grass taken to a suitable collection center for proper dis- and dirt which may have accumulated. At the start posal. -
Page 10: Service Information
Service information We have competent service partners in all countries named on the guarantee certi cate whose contact details can also be found on the guarantee certi cate. These partners will help you with all service re- quests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables. - Page 11 Warranty certi cate Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card.
Need help?
Do you have a question about the GC-HM 300 and is the answer not in the manual?
Questions and answers