Advertisement
Breville Quiet Boil Technology
Your Breville ikon™ Quiet Boil Kettle includes Quiet Boil Technology, a new development that will
make boiling water in the kettle a quieter experience.
please carefully read the following instructions
how it works
The innovative Quiet Boil Technology reduces the size of the water bubbles, minimising the noise
level during heating. It is only at boiling point that a light bubbling noise can be heard which will
indicate that the water has boiled.
maintaining the Quiet Boil Technology
Through regular use over time, scale can build up in the kettle that can affect the performance of
the Quiet Boil Technology as well as the life of the kettle. Lime and Phosphate are common forms of
scale that can damage your kettle.
Lime scale, a harmless mineral, comes in the appearance of white, coloured or rusty-looking build
up on the inner walls of the kettle. Phosphate scale can't be seen, however, it can cause the water to
appear cloudy when heated.
To prevent scale from damaging your kettle, ensure that the kettle is de-scaled regularly. This is done
by emptying the kettle after use and not allowing water to stand in the kettle overnight.
6
operating your Breville ikon™ Quiet Boil Kettle
Before first use
Remove any promotional material attached to
your kettle. It is recommended that before first
use the kettle is filled to the maximum level,
boiled and water discarded. Your kettle will only
operate when positioned on the power base
with the On/Off switch in the 'On' position. The
kettle will automatically switch off once the
water has boiled.
operation of your kettle
1.
To fill the kettle, remove it from the power
base and open the lid by pressing the lid
release button. Fill with the desired amount
of water. Always fill the kettle between
the minimum and maximum marks on the
water window. Too little water will result in
the kettle switching off before the water has
boiled.
.
Ensure that the lid is locked firmly into
place. Place the kettle firmly onto the power
base. Power plug the power cord into
0/40V power point and switch 'On'.
.
Press the On/Off switch to the 'On' position.
The power 'On' light and the water gauge
will illuminate.
always fill the kettle between the minimum
(min) and the maximum (max) marks on the
exterior of the kettle. Too little water will result
in the kettle switching "off" before the water
has boiled. filling above the maximum mark on
the exterior of the kettle may result in boiling
water splashing from the kettle.
This applianCe is designed for The Boiling of drinKing QualiTy waTer only, never
use iT To heaT or Boil any oTher liQuids or foodsTuffs. The lid should always Be
firmly in plaCe and loCKed Closed Before use.
This kettle must only be used with the power
base supplied. use caution when pouring water
from your kettle, as boiling water will scald. do
not pour the water too quickly.
The kettle will automatically switch 'Off' once
the water has boiled. Lift the kettle from the
power base and pour the water. Take care to
hold the kettle level, especially when filled
to the maximum level. To re-boil it may be
necessary to wait for a few seconds to allow
the control to reset.
The kettle may be stored on its power base
when not in use. The power point should be
switched off and the appliance power plug
unpower plugged from the power when not in
use.
safety boil dry protection
The kettle is fitted with a safety device, which
protects against overheating should the
appliance be operated with insufficient water. If
this occurs the kettle will stop heating. Switch
'Off' at the power point and allow kettle to
cool before refilling. The safety device will
automatically reset when the kettle has cooled
down.
For additional safety your kettle is fitted with
an additional thermal cut out. In the event of
overheating, the kettle will automatically shut
down to prevent further damage. Should this
occur, take your kettle to an authorised Breville
Service Centre.
7
Advertisement
