Related Manuals for SSP MRP102
Summary of Contents for SSP MRP102
- Page 1 INSTRUCTION MANUAL Router MRP102 013290 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model MRP102 Collet chuck capacity 12 mm or 1/2" Plunge capacity 0 - 60 mm No load speed (min 22,000 Overall height 300 mm Net weight 5.5 kg Safety class • Due to our continuing program of research and development, the specifications herein are subject to change without notice. -
Page 3: Router Safety Warnings
Keep cord away from heat, oil, sharp edges or 19. Do not use the power tool if the switch does moving parts. Damaged or entangled cords not turn it on and off. Any power tool that increase the risk of electric shock. cannot be controlled with the switch is dangerous When operating a power tool outdoors, use an and must be repaired. -
Page 4: Functional Description
Handle the bits very carefully. FUNCTIONAL DESCRIPTION Check the bit carefully for cracks or damage before operation. Replace cracked damaged bit immediately. CAUTION: Avoid cutting nails. Inspect for and remove all Always be sure that the tool is switched off and •... -
Page 5: Operation
CAUTION: ASSEMBLY Since excessive cutting may cause overload of the • motor or difficulty in controlling the tool, the depth CAUTION: of cut should not be more than 20 mm at a pass Always be sure that the tool is switched off and when cutting grooves. - Page 6 Set the tool base on the workpiece to be cut without the Straight guide (Type A) (Optional accessory) bit making any contact. Then turn the tool on and wait 1. Thumb screw until the bit attains full speed. Lower the tool body and move the tool forward over the workpiece surface, 2.
- Page 7 Trimmer guide (Type A) (Optional accessory) Templet guide 1. Thumb screw (A) 2. Guide holder 3. Fine adjusting screw 4. Thumb screw (B) 5. Thumb screw (C) 6. Trimmer guide 7. Guide roller 013305 013301 Install the trimmer guide on the guide holder with the The templet guide provides a sleeve through which the thumb screw (B).
-
Page 8: Maintenance
Dust cover (For tool with the knob) (optional 1. Support accessory) 2. Lock lever 1. Screw 2. Dust cover 004940 Then connect a vacuum cleaner to the vacuum head. 013307 Dust cover prevents sawdust from being drawn into the tool in the inverted position. Install the dust cover as illustrated when using the tool with a router stand available in the market. -
Page 9: Optional Accessories
For tool with the knob OPTIONAL ACCESSORIES CAUTION: Router bits Be sure to re-install the knob after inserting new • Straight bit carbon brush. 1. Knob 005116 013310 Release the lock lever and remove the knob by turning it counterclockwise. The compression spring will come out of the knob, so be careful not to lose the 1/4"... - Page 10 "V"Grooving bit Drill point double flush trimming bit 005118 005121 1/4" 006454 006457 Dovetail bit Slotting cutter 005119 005122 14.5 15SE 3/8" 1/2" 14.5 14.5 15LE 3/8" 1/2" 006458 3/8" 006455 Drill point flush trimming bit 005120 006456...
- Page 11 Board-jointing bit Chamfering bit 005123 005126 1/2" 006461 005124 006459 005127 Corner rounding bit 006462 Beading bit 005125 006460 005128 1/2" 006463...
- Page 12 Cove beading bit Ball bearing chamfering bit 005132 005129 1/4" 006464 Ball bearing flush trimming bit 006467 Ball bearing beading bit 005130 005133 1/4" 006465 Ball bearing corner rounding bit 006468 Ball bearing cove beading bit 005131 005134 1/4" 006466 006469...
- Page 13 Ball bearing roman ogee bit 005135 006470 Double ball bearing round corner bit 005136 1/2" 006471...
- Page 16 Makita Corporation www.makita.com 885173A933...
Need help?
Do you have a question about the MRP102 and is the answer not in the manual?
Questions and answers