Advertisement
Operating instructions
celexon Expert electrically
height-adjustable display trolley
Oslo / Oslo Max
Thank you for purchasing this product. For optimum performance and safety, please
read these instructions carefully before connecting or operating this product. Please
retain these instructions for future use.
Version: 32424_102
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Celexon Oslo
Summary of Contents for Celexon Oslo
- Page 1 Operating instructions celexon Expert electrically height-adjustable display trolley Oslo / Oslo Max Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting or operating this product. Please retain these instructions for future use.
- Page 2 Contact the dealer immediately, from whom you purchased the product or celexon directly (Web: www.celexon.co.uk, Mail: info@ celexon.co.uk) for further information.
- Page 3 Incorrect installation or use may also invalidate the warranty. • If you are unsure about the use of the product, please contact your specialist per- sonnel, your dealer or celexon directly (Web: www.celexon.co.uk, Mail: info@celexon. co.uk). • Technical changes and errors excepted.
-
Page 4: Battery Instructions
Do not use damaged or leaking batteries, as these can release hazardous chemicals. TECHNICAL DATA • Suitable for display sizes: Oslo: 55” to 90” Oslo Max: 80” to 110” • Suitable for VESA standard: Oslo: 200x200 - 900x600 Oslo Max: 200x200 - 1200x600 •... - Page 5 IN THE BOX 1x left strut (A) 1x right strut (B) 4x roller base (C) 1x motor element (D) 1x cross strut (E) 1x shelf (F) 1x left VESA mount (G) 1x right VESA mount (H) 1x Power cable (K) 2X cable management (I) 1x remote control (J) 4x M8x25 mm (B1)
- Page 6 DIMENSIONS OSLO 1.063 mm 200 - 900 mm 1.070 mm 962,5 mm Control element...
- Page 7 DIMENSIONS OSLO MAX 1.413 mm 200 - 1.200 mm 1.420 mm 962,5 mm Control element...
-
Page 8: Installation Notes
INSTALLATION NOTES During assembly, ensure that the display and the associated accessories do not come into contact with the ceiling, door frames or similar obstacles when raising the display stand. This could lead to injuries or damage to the products. Note: Ensure that the display used, including accessories, does not exceed the maximum load capacity of 90 kg. - Page 9 STEP 1 I ASSEMBLING THE CHASSIS Make sure that both columns are the same height. If one of the columns is higher, carefully push it down until it reaches the same height as the other. Fig. 4...
- Page 10 STEP 1 I ASSEMBLING THE CHASSIS Screw the shelf F to the motor element D using the screws D2. Tighten the screws firmly but do not overtighten them to avoid damage. Fig. 5...
- Page 11 STEP 1 I ASSEMBLING THE CHASSIS Fit the motor element to the roller feet. Make sure that the sides with the addi- tional holes point inwards so that the motor can engage in the threads provid- ed. This step should be carried out by at least two persons. Fasten the motor element to the roller feet from the outside using screws A2 and washers C2 to the roller feet.
- Page 12 STEP 2 I MOUNTING DISPLAY ASSEMBLY Align the cross strut for mounting the display holder so that the marking points forwards towards the shelf (see Fig. 7). Fasten the cross strut to the roller feet using the A2 screws and C2 washers. Tighten the screws firmly but do not overtighten them, to avoid damage.
-
Page 13: Step 3 I Operation
STEP 3 I OPERATION Attention: Before attaching the display, initialise the display stand, after you have connected it to the power supply. To do this, press the reset button the rear control panel and hold it down until ‘1750’ appears on the display. The display stand is then ready to be loaded and used normally. - Page 14 STEP 4 I MOUNTING THE DISPLAY Mount the two VESA brackets G and H on the display. Only use screws in ac- cordance with the manufacturer‘s instructions for your display. Make sure that the screws are not screwed too far into the display otherwise the display may be damaged.
- Page 15 STEP 4 I MOUNTING THE DISPLAY To prevent the display from colliding with the shelf, adjust the bracket to the correct height before hanging the display. Make sure that the display stand is in the lowest position. The VESA brackets have two recesses that can be used to mount the bracket at different heights on the display stand.
- Page 16 STEP 5 I WIRING Make sure that there are no people or objects in the area of travel when the display stand is in use. Attach the two brackets I for the cable management to the castor base and route the outgoing cables through these brackets. Fig.
-
Page 17: Step 6 I Remote Control
STEP 6 I REMOTE CONTROL Replacing the battery in the remote control: Loosen the screw on the back of the battery cover. Remove the cover. Replace the battery, ensuring that the polarity is correct. Place the cover back on the battery compartment. - Page 18 STEP 7 I MOUNTING OPTIONAL CAMERA SHELF You have the option of mounting the supplied camera shelf on the display stand. To do this, attach the camera shelf M to the mounting strut L using the screw O. Fig. 17 Attach the entire camera shelf to the back of the display stand using screws D2, as shown in Figure 18.
- Page 19 Oslo / Oslo Max Hereby celexon Europe GmbH declares that the celexon Expert electrically height-adjustable display trolley Oslo / Oslo Max complies with the directive 2014/53/ EU. The EU declaration of conformity can be downloaded from the following address: www.celexon.de/zertifikate The symbol indicates the separate collection of electrical and elec- tronic devices in EU countries.
Need help?
Do you have a question about the Oslo and is the answer not in the manual?
Questions and answers