Digitales Messgerät DSMG 96 Th
mit zwei Grenzwertkontakten
Sicherheitshinweise
Betriebsanleitung beachten!
Das beschriebene Gerät darf ausschließlich durch qualifizierte Elektrofachkräfte
gemäß DIN EN 50110-1/-2 sowie IEC 60364 installiert werden. Prüfen Sie vor
Inbetriebnahme das Gerät auf Transportschäden. Bei Beschädigungen darf das
Gerät nicht in Betrieb genommen werden. Halten Sie bei der Verwendung des
Gerätes die geltenden Gesetze, Normen und Bestimmungen ein. Installieren Sie
das Gerät nur in trockenen Räumen. Die Montage des Gerätes darf nicht auf oder
an leicht entzündlichen Materialien erfolgen. Eine nicht bestimmungsgemäße
Nutzung sowie die Nichtbeachtung dieser Anwendungshinweise haben den
Verlust der Gewährleistung bzw. Garantie zur Folge. Das Gerät ist bei sachgemäßer
Anwendung wartungsfrei.
Warnung! Schutz gegen gefährliche Körperströme.
Bei Anwendungen mit hohen Arbeitsspannungen ist auf ausreichend Abstand bzw.
Isolation zu anderen Geräten und auf Berührungsschutz zu achten. Gefährliche
elektrische Spannung kann zu elektrischem Schlag und Verbrennungen führen.
Schalten Sie immer alle verwendeten Spannungsversorgungen für das Gerät ab,
bevor Sie das Gerät montieren, installieren, Störungen beheben oder
Wartungsarbeiten vornehmen.
Achtung!
Auf Schutzmaßnahmen gegen elektrostatische Entladungen (ESD) achten.
Die Geräte dürfen nur fachgerecht entsorgt werden!
Weitere Informationen unter www.mueller-ziegler.de.
Konformität
Dieses Gerät entspricht den Bestimmungen der EMV-Richtlinie 2014/30/EU, der
Niederspannungsrichtlinie 2014/35/EU, sowie der RoHS-Richtlinie 2011/65/EU.
Anwendung
Das digitale Messgerät DSMG 96 Th kann zur Messung der Temperatur in Verbindung mit
einem Thermoelement eingesetzt werden.
Funktion
Die Messgröße wird einem 4-stelligen A/D-Wandler zugeführt. Die Wandlung geschieht nach
dem "Dual-Slope" Prinzip. Die Vergleichsstellenkompensation erfolgt intern mit einem PT100
Temperaturfühler. Die Anzeige erfolgt durch Siebensegment-Niedrigstrom LED-Anzeigen. Bei
Leitungsbruch des Thermoelements blinkt die Anzeige. Die Messgröße wird ständig mit den
eingestellten Grenzwerten verglichen. Bei Erreichen der Grenzwerte werden die
entsprechenden Grenzwertkontakte geschalten. Die Programmierung der Grenzwerte erfolgt
frontseitig über die Folientasten. Das Messgerät besitzt einen Minimal- und
Maximalwertspeicher. Die Nullpunktkorrektur erfolgt automatisch. Der Anzeigebereich lässt
sich nach Abnehmen der Frontscheibe verändern.
Technische Daten
Eingangsdaten
Eingangsgröße
Thermoelement, Typ bei Bestellung angeben
Nennwerte nach
Typ B (DIN EN 60584-1)
DIN EN 60584
Typ E (DIN EN 60584-1)
Typ J (DIN EN 60584-1)
Typ K (DIN EN 60584-1)
Typ N (DIN EN 60584-1)
Typ R (DIN EN 60584-1)
Typ S (DIN EN 60584-1)
Typ T (DIN EN 60584-1)
interne Kaltstellen-
0-80 °C
kompensation
Genauigkeit
+/-0,2 % vom Messwert +/-2 Digit
Messprinzip
Dual-Slope-Integration
Messrate
ca. 3 Messungen pro Sekunde
Anzeigen
Anzeigen
LED-Siebensegment-Niedrigstrom, 13 mm hoch, rot, 4-stellig
2 rote LED's für Grenzwertüberschreitung
Polarität
durch Minus (-) Anzeige
Überlauf
blinkende Anzeige
Auflösung
+/- 9999 Digit
+100 ...+1820 °C,
-270 ...+1000 °C,
-210 ...+1200 °C,
-270 ...+1372 °C,
-270 ...+1300 °C,
-50 ...+1768 °C,
-50 ...+1768 °C,
-270 ...+400 °C
Müller + Ziegler GmbH, Industriestr. 23, 91710 Gunzenhausen
Tel. +49 (0)9831 5004-0
www.mueller-ziegler.de
Digital measuring instrument DSMG 96 Th
with two limit value contacts
Safety Informations
Observe instructions!
The device described in these instructions shall only be installed by a qualified
electrician according to both EN 50110-1/-2 and IEC 60364. Before startup,
check the device for any damage that may have occurred during shipping. The
device shall not be put into operation in the event of mechanical damage.
Observe in the use of the device the applicable laws, standards and regulations.
Only install this device in dry rooms. Do not install the devices on or in the
vicinity of easily flammable materials. Improper use and failure to follow these
instructions for use will render the warranty or guarantee null and void. The
device is maintenance-free when used correctly.
Warning! Protection against electric shock.
For applications with high working voltages, take measures to prevent
accidental contact and make sure that there is sufficient distance or insulation
between adjacent devices! High voltage can cause electric shock or burns.
Switch off all power to the device prior to performing any installation, repair or
maintenance work.
Caution!
Be sure to take protective measures against electrostatic discharge (ESD).
The devices must be disposed of a proper manner!
More information at www.mueller-ziegler.de.
Conformity
The device conforms to the requirements of the EMC Directive 2014/30/EU, the
Low Voltage Directive 2014/35/EU, as well as the RoHS Directive 2011/65/EU.
Application
The digital measuring instrument DSMG 96 Th may be used for measuring the temperature
in connection with a thermocouple.
Function
The measurand is sent to a 4-digit A/D-converter. The conversion is made following the
„Dual Slope" principle. The cold junction comparison is made internal with a PT100
temperature sensor. The values are indicated by 7-segment low-power LED displays. The
measurand is continuously compared to the set limit values. As soon as the limit values
are reached, the related limit value contacts are switched. The programming of the limit
values is done via the front panel using membrane keys. The measuring instrument is
equipped with a min/max value memory. The zero point compensation is done
automatically. The display range may be changed after removing the front panel.
Technical Data
Input Data
Input variable
thermocouple, specify the thermocouple type when ordering
Rated values
type B (EN 60584-1)
type E (EN 60584-1)
type J (EN 60584-1)
type K (EN 60584-1)
type N (EN 60584-1)
type R (EN 60584-1)
type S (EN 60584-1)
type T (EN 60584-1)
Internal cold junction
0-80 °C
comparision
Accuracy
+/-0,2 % of measured value +/- 2 digits
Measuring principle
Dual-Slope-integration
Sampling rate
approx. 3 measurements per second
Indicators
Display
LED 7-segment low-power, height 13 mm, red, 4-digit
2 red LED for limit value violation
Polarity
by negative (-) display
Overflow
flashing display
Resolution
+/- 9999 digit
info@mueller-ziegler.de
12.03.2025
+100 ...+1820 °C,
-270 ...+1000 °C,
-210 ...+1200 °C,
-270 ...+1372 °C,
-270 ...+1300 °C,
-50 ...+1768 °C,
-50 ...+1768 °C,
-270 ...+400 °C
Need help?
Do you have a question about the DSMG 96 Th and is the answer not in the manual?
Questions and answers