Barska AX13744 Manual

Manual for Biometric Keypad Safe
Read all instructions before using this safe
WARNING
- In Factory Default mode, the safe CANNOT be opened by
any fingerprint. For security purposes, please promptly
register your own fingerprint before starting to use the safe.
The initial Pin Code A: 1234 and Code B:123456. Kindly
follow the Fingerprint/Password Set Up to establish your
personalized fingerprint/password.
- Safe can be opened by either Fingerprint, Pin code, and /or
Emergency Keys.
- Test and Store emergency keys in a secure place, NOT
inside of the safe.
- Avoid leaving safe door open and unattended; it will allow
unauthorized individuals to add their fingerprints and/or
reprogram the safe, gaining full access to the safe and
the contents.
- To maximize the security and performance of the safe, test
registered fingerprints every 6 months.
- Test and make sure the safe works properly before
mounting. Once tested, mount the safe before use.
- Keep children away from safe; they should not play with or
around the safe at anytime. Children at play could
accidentally pull on the safe or accidentally pull on the safe
door causing safe to tip over if not properly mounted.
- Failure to follow these warnings could result in serious injury
or death.
PARTS OF THE SAFE
A
C
B
D
E
G
F
A. Battery Compartment E. Keypad
B. Initialization Button
F. External 9V Battery Source
C. Handle G. Emergency Key Access
D. Fingerprint Scanner
©2024 BARSKA® | 855 Towne Center Drive | Pomona, CA 91767
OPENING SAFE WITH ACCESS KEY
1. To expose the key access, rotate the keypad
counter-clockwise smoothly to remove it from the door
2. Insert emergency key into key access and turn clockwise;
turn handle to unlocked position and open the safe.
Remove key and keep in a secure location.
INSTALL BATTERIES
1. With the door open, remove the battery cover by sliding
the cover.
2. Insert 4 AA batteries by lining them up in a manner as
indicated by the "+" and "-"signs.
3. Put the arrow of the battery cover align to the arrow on the
compartment, slide the batteries cover back into place.
Restore the battery compartment cover.
NOTE:
DO NOT use any other type of non-alkaline battery.
DO NOT mix new and old batteries.
External Battery Source
9V battery can be used as an external power source. (9V
battery not included) Please remove the bottom black sticker
of keypad, then place 9V battery, touch the metal contacts
under the fingerprint or pin code mode. Safe should power
up, if not switch the polarity of the 9V battery.
LOCK/UNLOCK SAFE
Single Entry Mode
Unlock Safe with Pin Code
1. On the keypad enter registered pin code 4-8 digits and
press "#" to confirm. Green light flashes with 2
short beeps.
2. Turn the handle to unlock position to open the safe door.
Unlock Safe with Fingerprint
1. On the scanner place registered fingerprint, green light
flashes with 2 short beeps.
2. Turn the handle to unlock position to open the safe door.
Lock Lock Safe
Close door and turn handle to lock position to lock the safe.
Unlock
FINGERPRINT REGISTRATION
1. With the safe open, press and release initialization button
located inside of the safe. Yellow light flashes with 2
short beeps.
2. Immediately place desired finger on fingerprint scanner,
yellow light flashes with 2 short beeps. Remove the finger
from fingerprint scanner.
3. Repeat step 2 two more times, 1 long beep will be heard.
Fingerprint Registration is completed.
4. Fingerprint Registration can be stored up to 20
different fingerprints.
Important: 1 Fingerprint registration required 3 times of
placing the finger on the scanner to complete.
Successful Registration
1 long beep will be heard and yellow light will flash off.
Unsuccessful Registration
3 short beeps will be heard.
NOTE:
1. DO NOT choose a fingerprint with a scar or cut.
2. Make sure your hands are clean without dusts.
3. Make sure your finger is flatly placed at the center of
fingerprint scanner for better identification.
4. In cold or dry climate conditions, your hands may be too
dry, it will affect your fingerprint registration. We
recommend to moisturize your hands and rub your fingers
before registering.
5. Testing a fingerprint that is not registered to make sure the
safe cannot be unlocked to complete the
registration process.
6. Please follow the steps " LOCK/UNLOCK SAFE " to test
successful registration.
PIN CODES REGISTRATION
Default code A:1234 and Code B:123456
Pin Code can be 4-8 digits
Code A
1. With the safe open, press and release initialization button
located inside of the safe. Yellow light flashes with 2
short beeps.
2. On the keypad input new desired Pin Code and press
" # " to confirm. 2 short beeps will be heard, Pin Code
registration is completed.
Code B
1. With the safe open, Press "00" on keypad.
2. Press and release initialization button located inside of the
safe. Yellow light flashes with 3 short beeps.
3. On the keypad input new desired Pin Code and press " # "
to confirm. 2 short beeps will be heard, Pin Code
registration is completed.
Successful Registration
2 short beeps will be heard.
Important
1. Testing a pin code that is registered to make sure the safe
can be unlocked to complete the registration process.
2. Please follow the steps " LOCK/UNLOCK SAFE " to test
successful registration
See reverse side for more information
9/24
BC808