Download Print this page
Dell P2424HT Teardown Manual
Dell P2424HT Teardown Manual

Dell P2424HT Teardown Manual

Touch usb-c-hub monitor
Hide thumbs Also See for P2424HT:

Advertisement

Quick Links

Mechanical Instruction
Disassembly Procedures:
Step
S1.Before
disassemble
S2.Remove the
STAND-BASE
ASS'Y
S3.Remove the
REAR COVER
Figure
Remark
Turn off power, Unplug
external cables from
product
Lay down the MNT on a
clean and soft surface.
Push the button to
remove the stand-base
ass'y.
Use a Philips-head
screwdriver to remove 4
screws for unlocking
mechanisms.
(No.1~4 screw
size=M4x10; Torque:
12±2kgf.cm)

Advertisement

loading
Need help?

Need help?

Do you have a question about the P2424HT and is the answer not in the manual?

Questions and answers

Summary of Contents for Dell P2424HT

  • Page 1 Mechanical Instruction Disassembly Procedures: Step Figure Remark Turn off power, Unplug S1.Before external cables from disassemble product Lay down the MNT on a S2.Remove the clean and soft surface. STAND-BASE Push the button to ASS’Y remove the stand-base ass’y. Use a Philips-head screwdriver to remove 4 screws for unlocking mechanisms.
  • Page 2 Use Penknife to seperate rear cover follow the arrows in sequence, then you can take out rear cover. S4. Disconnect the Disconnect the pins. connectors Tear off 2 pieces of S5. Tear off the aluminum foil and 3 tapes pieces of tapes.
  • Page 3 S6. Disconnect the connectors and Disconnect the remove the connectors and remove Speaker the Speaker Use a Philips-head screwdriver to remove 1 screws for unlocking the main frame ( No.1 screw size=M3x4, Torque: 3±0.5kgf.cm) Disconnect the pin and S7. Remove the FFC cable.
  • Page 4 Use a Philips-head screwdriver to remove 8 screws for unlocking the main board, power board. (No.1~8 screw size=M3x6, Torque=6±1kgf.cm Disconnect the connectors...
  • Page 5 The main frame Use a Philips-head screwdriver to remove 11 S8. Remove the screws for unlocking the middle frame Panel and middle frame (No.1~11 screw size=M3x4, Torque=3±0.5kgf.cm) Use a Philips-head screwdriver to remove 1 screws for disassembling the key board. ( No.1 screw size=Q2x2.5, S9.
  • Page 6 Use a Philips-head screwdriver to remove 3 screws for disassembling S10. Remove USB the USB board. board from rear ( No.1~3 screw cover size=Q3x4, Torque=4±1kgf.cm) Use a Philips-head screwdriver to remove 3 screws for disassembling S11. Remove Key the key board. board from rear ( No.1~3 screw cover...
  • Page 7 8.1 Product material information The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC. Capacitors / condensers (containing Product has Capacitors PCB/PCT) Mercury containing components No used Batteries No used...
  • Page 8 Step Figure Remark Remove electrolyte capacitors (red mark) from printed circuit boards Remove the big Take out bulk cap capacitors pin solder with soldering iron and absorber Lift the bulk cap up and take it away from the...
  • Page 9 8.2 Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description: - Phillip-head Screwdriver - Hexagonal Screwdriver - Penknife - Soldering iron and absorber...

This manual is also suitable for:

G2724d