Glendinning CRMA 50 Installation & Operation Manual

Power cord retrieval & storage system
Hide thumbs Also See for CRMA 50:

Advertisement

Power Cord Retrieval & Storage System
The CRMA Cordreel has been designed
for manual pay out and motorized retraction
of your shore power cable.
The Cordreel can store 50amp 125/250
volt shore power cable and European 63amp
250volt shore power cable.
1.0 P
D
RODUCT
ESCRIPTION
CRMA 50
CRMA50-XX-YY
White—50 amp cable
50' long
50amp Twist lock
plug w/ lanyard
Glendinning Products, LLC. 740 Century Circle Conway, SC 29526
CRMA Technical Manual Rev. 4.4
INSTALLATION & OPERATION MANUAL
XX – DC voltage
YY—Cable Type
5' long pigtail
Table of Contents
Anodized Aluminum
Frame
63 amp Twistlock
plug w/ lanyard
(std.)
Waterproof switch and
nameplate assembly w/ 10'
wires (all CRMA units)
Phone: 1(843)399-6146
1) Product Description
2) Product Dimensions
3) Wiring Diagram
4) Installation
5) Operating Instructions
6) Maintenance
7) Troubleshooting
8) Accessories
Appendix 1
Appendix 2
CRMA 63
CRMA63-XX-YY
Yellow—63 amp cable
Fax: 1(843)399-5005
20m long
2m long pigtail
(std.)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CRMA 50 and is the answer not in the manual?

Questions and answers

Summary of Contents for Glendinning CRMA 50

  • Page 1 5’ long pigtail 2m long pigtail (std.) (std.) Waterproof switch and nameplate assembly w/ 10’ wires (all CRMA units) Glendinning Products, LLC. 740 Century Circle Conway, SC 29526 Phone: 1(843)399-6146 Fax: 1(843)399-5005 CRMA Technical Manual Rev. 4.4...
  • Page 2: Wiring Diagram

    2.0 P RODUCT IMENSIONS CRMA 50/63 Weight: 62 lbs. (w/ 50’ 6/4 cable) 3.0 W IRING IAGRAM OPTIONAL Hawse Pipe Assembly CRM # 04079-CRM Hawse Pipe w/ roller assembly # 04079-CRM-LS Hawse Pipe w/ rollers and limit switch assembly AC Power “Pigtail”...
  • Page 3 4.0 C ORDREEL NSTALLATION 4.1 Before You Start the Installation ✓ There are a few requirements that NEED to be followed in ✓ the planning of your installation: SHORE POWER CABLE ROUTING FROM CORD REEL TO BOAT EXIT (Normally through hatch or Hawse pipe) •...
  • Page 4: Installation Configurations

    4.0 C ORDREEL NSTALLATION 4.2 Installation Configurations The Cordreel (50/63) is capable of being mounted in multiple configurations: STANDARD MOUNTING CONFIGURATIONS: Standard Standard—Top Mount Exit Standard—Rear Mount Exit SIDE MOUNTING CONFIGURATIONS: !! IMPORTANT !! Side Mount—Vertical Exit Side Mount—Horizontal Exit •...
  • Page 5 4.4 Installing the Hawse Pipe (optional accessory) Part#: 04079-CRM — Hawse Pipe w/ Guide Roller Assembly The installation of the Hawse Pipe is optional. 04079-CRM-LS — Hawse Pipe w/ Guide Roller In- You may also use your existing Hawse Pipe or any Limit Switch Assembly storage space door that is accessible to where you Clearance hole 17/64...
  • Page 6: Control Switch

    4.6 DC Wire Connection The Cordreel comes with (2) 14 gauge wires exiting from the gear motor cover. • These wires should be connected to the 12 or 24 VDC power source depending on unit purchased (see label on unit for correct voltage). •...
  • Page 7: Maintenance

    UCTS, LLC. option, the complete unit replaced and returned to the consumer, shipping charges prepaid. 5. GLENDINNING PRODUCTS, LLC. does not assume the costs of removal and/or installation of the product or any other incidental costs which may arise as a result of any defect in materials or workmanship.
  • Page 8 8.0 A CCESSORIES PART# Description 04054 Guide Roller Assembly with Plate Remote Control System 12/24V, Includes (2) transmitters, (1) receiver, (1) 04154-1B antenna, and (1) wire harness. See P. 2 for wiring information. 04079-CRM Stainless Steel Hawse Pipe w/ Guide Roller Assembly 04079-CRM-LS Stainless Steel Hawse Pipe w/ Guide Roller Assembly and Limit Switch Bracketing to install pipe accessories onto unit—See Appendix 1 for more infor-...
  • Page 9 APPENDIX 1 CR Extension Bracket assembly – Part# 04210 This bracket assembly can be attached to any CRMA 16/30/32/50/63 guide roller assembly. Allows simple attachment of pipe extension assemblies, pipe clamp assemblies. 3” schdl 40 PVC Pipe Extra mounting holes for 50004 Pipe Extension Plate and Guide Roller Assembly.
  • Page 10 APPENDIX 1 (CONTINUED) Top Cable Exit Standard Cable Exit...
  • Page 11 APPENDIX 2 19846-5 – CRMA50 Side Mount Roller Assembly Instructions When mounting the CRMA50 unit on its’s side (which is not ideal) there are a few requirements that must be followed or else the unit will not store the cable correctly. 1) Most importantly –...
  • Page 12 APPENDIX 2 (CONTINUED) STEP 1 Unit is laying on its side as shipped from Glendinning STEP 2 Move roller assembly and both brackets to bottom of unit as shown. Move roller assembly from bottom of unit the in between the brackets that were just moved.

This manual is also suitable for:

Crma 63

Table of Contents