Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for AFL U Series
Summary of Contents for AFL U Series
- Page 1 Installation Instructions 6RU (864f) Front-Access V-Panel (FVP) Series...
- Page 2 Never look into the end of a ber or connector which may have a laser coupled to it. Should accidental eye exposure to laser light be suspected, arrange for an eye examination immediately. © AFL. All rights reserved Series...
-
Page 3: Component Overview
U-Series 6RU Front-Access V-Panel Component Overview Item Item Description Number U-Series 6RU Front-Access V-Panel Chassis 288f Modular Drawer 6RU Shipping Bracket U-Series Patch Adapter Plate 288f Ribbon Mass Splice Tray 25mm PVC Blind Blanking Grommet (Black) © AFL. All rights reserved Series... - Page 4 (T) 6RU Rear Door + (S) Front Labels Panel Slide Latches Mount (V) 6RU LHS Door (W) 6U Front Door (X) Breakout Bracket (Y) Cable Entrance Cover (Z) Grommet Mount Assembly Assembly with 2 pcs Brush Strip © AFL. All rights reserved Series...
-
Page 5: Panel Mounting
Partially tighten cage nut screws in positions Insert cage nuts in positions shown on both shown using screwdriver. left- and right-hand-side of rack. © AFL. All rights reserved Series... - Page 6 Separate out and tape up 144f ber bundle slide braid onto ber braid tube, then tape ends as per splicing schedule and feed into braid at both ends of tubing to secure. ber braid tube. © AFL. All rights reserved Series...
- Page 7 25mm (1”) approx. Repeat steps 12-15, ensuring all ber has Attach cable to clamp with hose clips and braided sleeve, and then tape braid sleeve at place braid tails into slots. cable jacket end. © AFL. All rights reserved Series...
- Page 8 (do not pull tight, leave natural slack curve). Cable Cable Cover Screw Positions Feed all cable braid tails through to front of panel and cable tie braids to T-slots. DO NOT Fit cable cover. OVER-TIGHTEN. © AFL. All rights reserved Series...
- Page 9 Cassette/ Splice Tray 1 Splice Tray 2 Pigtail Tail (Bottom Tray) (Top Tray) Number Cassette to splice tray ber map: cassettes 1-6 into Splice Tray 1 (BOTTOM), cassettes 7-12 into Splice Tray 2 (TOP). © AFL. All rights reserved Series...
- Page 10 Splice Tray 2 (TOP): Tie off cable braid to splice tray. Starting with internal pigtail #7 (RED), splice to cable ber (GREEN), place splice protector into YELLOW holder. Coil ber in suggested route shown. © AFL. All rights reserved Series...
- Page 11 Push/Pull Handle Slide drawer back out to fully extended, gently Push drawer back into panel so that it is fully pull braid tail to straighten, and make slack retracted. coil, securing with Velcro as shown. © AFL. All rights reserved Series...
- Page 12 Repeat steps 25-30 for middle and top and tighten. Repeat for other side. drawers. Labels Attach front door to mounts with spring plungers. Door pivots and latches closed with swell latches. Stick relevant port label to rear of door. © AFL. All rights reserved Series...
-
Page 13: Additional Steps
Right Labels Left Labels All labels All labels centrally centrally aligned aligned to between tabs they are the screws applied to The complete V-Panel with labels applied should look as shown above. © AFL. All rights reserved Series... - Page 14 Thank you for choosing AFL AFL reserves the right to make changes to this Installation Instruction at any time without notice AFL6RUFVP231123...
Need help?
Do you have a question about the U Series and is the answer not in the manual?
Questions and answers