McIntosh C1000 - SOLID STATETUBE PREAMPLIFIER TUBE AND SOLID STATE REAR PANEL CONNECTIONS Manual

2
A
CD (6), CDR (5)
and D/A (7) RIGHT
Channel INPUTS
CDR (5) RIGHT
(Balanced) accept
Channel OUPTUTS
high level program
(Balanced) contain
source signals
the selected Record
Source Signal for
recorders
MAIN RIGHT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times
MAIN/SPKR 1 and 2 RIGHT
Channel OUTPUTS (Balanced)
contain Listen signals and may be
assigned either as two additional
Main Outputs (active all the time)
or switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SPKR 1 and 2 RIGHT Chan-
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SRVR (4) and CDR (5)
RIGHT Channel OUPTUTS
(Unbalanced) contain the
selected Record Source Signal
for recorders
PROCESSOR RIGHT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode
PROCESSOR RIGHT Channel RECORD
TO and FROM allows an external signal
processor to be connected for use in the
Record mode
TUNER (3), DVD (1), SRVR (4)
and AUX (2), RIGHT Channel
INPUTS (un-balanced) accept
high level program source signals
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549
C1000 Preamplifier Rear Panel Connections
RIGHT PREAMPLIFIER
INPUT A Connector accepts
RECORD LINK INPUTS (Bal-
the custom McIntosh 21
anced) connect to the Record Link Conductor Cable. This cable
RIGHT Channel Input on the
connects to the C1000C
C1000T Preamplifier when the RIGHT CONTROLLER
C1000P and a C1000T Preampli-
OUTPUT A. It supplies the
fiers are both connected to the control signals and power
same C1000C Controller, allowing
supply voltages for the Right
for the sharing of their inputs for Channel Circuitry in the
recording purposes
Preamplifier
PHONO INPUTS RIGHT MM
(8) accepts signals from a Moving
Magnet Phono Cartridge. MC (9)
Input accepts the low level signals
from a Moving Coil Phono Car-
tridge
Part No. 04100200
LEFT PREAMPLIFIER
INPUT B Connector ac-
RECORD LINK INPUTS (Bal-
cepts the custom McIn-
tosh 21 Conductor Cable. anced) connect to the Record
Link LEFT Channel Input on the
This cable connects to the
C1000C LEFT CONTROL- C1000T Preamplifier when the
C1000P and a C1000T Preampli-
LER OUTPUT B. It sup-
plies the control signals and fiers are both connected to the
power supply voltages for same C1000C Controller, allowing
the Left Channel Circuitry for the sharing of their inputs for
in the Preamplifier recording purposes
GND (Ground)
connectors for
PHONO INPUTS LEFT MM (8)
connecting
accepts signals from a Moving
the Turntable
Magnet Phono Cartridge. MC (9)
Ground Wire
Input accepts the low level signals
to the C1000P
from a Moving Coil Phono Car-
Chassis
tridge
CD (6), CDR (5) and
D/A (7) LEFT Chan-
CDR (5) LEFT
nel INPUTS (Bal-
Channel OUPTUTS
anced) accept high
(Balanced) contain
level program source
the selected Record
signals
Source Signal for
recorders
MAIN LEFT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times
MAIN/SPKR 1 and 2 LEFT
Channel OUTPUTS (Bal-
anced) contain Listen signals
and may be assigned either as
two additional Main Out-
puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SPKR 1 and 2 LEFT Chan-
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SRVR (4) and CDR (5) LEFT
Channel OUPTUTS (Unbalanced)
contain the selected Record Source
Signal for recorders
PROCESSOR LEFT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode
PROCESSOR LEFT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode
TUNER (3), DVD (1), SRVR (4)
and AUX (2), LEFT Channel IN-
PUTS (un-balanced) accept high
level program source signals