Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Duco iAV Control valve
Summary of Contents for Duco iAV Control valve
- Page 1 iAV Control valve ENGLISH Quick Start L1020502 (Revision G | 08.04.2025)
-
Page 2: Table Of Contents
Installation, connection, maintenance and repairs are to be carried out by an accredited installer� The electronic components of this product may be live� Avoid contact with water� DUCO, HANDELSSTRAAT 19 VEURNE, B-8630 Vero DUCO - Handelsstraat 19 - 8630 Veurne - Belgium tel +32 58 33 00 33 - info@duco.eu - www.duco.eu L1020502 Quick start iAV control valve (Revision G | 08.04.2025) -
Page 3: Application
Room independently of each other� Sensor� The valves operate independently of each other� Controller Controller Component Component CENTRAL CENTRAL EXTRACTION EXTRACTION ZONAL ZONAL EXTRACTION EXTRACTION L1020502 Quick start iAV control valve (Revision G | 08.04.2025) - Page 4 , humidity one or more room sensors can be provided� or sensorless)� In the case of sensorless valves, one or more room sensors can be provided� Controller Controller Component Component L1020502 Quick start iAV control valve (Revision G | 08.04.2025)
-
Page 5: Regulations And Safety Instructions
When installing the unit, always follow the safety instructions in the manual� Failure to follow these safety instructions, warnings, notes and instructions could result in damage to the iAV Control Valve or in personal injury for which DUCO NV cannot be held liable�... -
Page 6: Connections And Buttons
Transitional phase (please wait) the actuator, this may take a few minutes) WHITE or OFF Normal BLUE Visualisation of the Actuator PCB when changes are made via the Controller or Duco Network Tool L1020502 Quick start iAV control valve (Revision G | 08.04.2025) -
Page 7: Wiring
2� Wired components can only be paired to iAV Control Valves as from product version 180327� Wired components only possible from iAV product version 180327 Restriction to a maximum of 300 metres Wired cabling L1020502 Quick start iAV control valve (Revision G | 08.04.2025) -
Page 8: Mounting
When closing, the white LED will dim until the LED is off� 2� Disconnect the cables only now� 3� Push the two ribbed tabs inwards in order to be able to slide the iAV Control Valve back out of the casing� L1020502 Quick start iAV control valve (Revision G | 08.04.2025) -
Page 9: Installation
Valve starts blinking red slowly� c� Tap 1 x on 'INST' of this component iAV Control Valve to pair it to the network� d� Repeat steps 3b and 3c for the remaining component iAV Control Valves in this zone� L1020502 Quick start iAV control valve (Revision G | 08.04.2025) -
Page 10: 06�B Other Operations
• Long press 'INST' again to remove all components under the iAV Control Valve� The LED will stop blinking� • Use the Duco Network Tool to read information from the components (see page 14 for more information)� • Never pair components to multiple iAV Control Valves at the same time�... -
Page 11: Calibration
For the system to work correctly, it needs to be configured� This helps ensure the quietest possible and most energy-efficient operation� See under the Tools heading at www�duco�eu for information about determining ventilation flow rates� The calibration procedure depends on whether iAV is used as a controller (standalone) or iAV as a component (external control)�... - Page 12 For quick and easy calibration, it is recommended to provide a CFR (Constant Flow Regulator) in each zone (flow rate = sum of underlying flow rates)� NOTE: the calibration procedure must be carried out on a windless day (maximum 2 Beaufort: leaves rustling, wind felt in face)� L1020502 Quick start iAV control valve (Revision G | 08.04.2025)
- Page 13 Measure any other vents within the current zone and adjust them via the exhaust vent� Work from the highest to the lowest flow rate� Exit the calibration mode of the current zone by pressing 'HIGH' on the iAV Control Valve� L1020502 Quick start iAV control valve (Revision G | 08.04.2025)
-
Page 14: Settings
This user-friendly software is the ideal way to change settings and detect problems in the system� The Duco Network Tool is issued to every installer after attending a free training course in the Duco Academy� Please consult our website or your DUCO dealer for more information�... -
Page 15: Maintenance
All warranty conditions concerning the DucoBox and DUCO's ventilation systems can be found on the DUCO website� All complaints are to be reported to DUCO by the DUCO distributor with a clear description and the order/invoice number under which the products were delivered� To do so, please fill out the complaint registration form, found on the DUCO website, mentioning the serial number and send it to service@duco�eu�... - Page 16 Installed by: L1020502 Document last modified on 08.04.2025 (revision G)
Need help?
Do you have a question about the iAV Control valve and is the answer not in the manual?
Questions and answers