Advertisement
Advertisement
Table of Contents
Related Manuals for NAIM FLATCAP 2 - MANUEL 2
Summary of Contents for NAIM FLATCAP 2 - MANUEL 2
- Page 1 O W N E R S M A N U A L P o w e r S u p p l i e s...
-
Page 2: Equipment Installation
EC Declarations of Conformity to Appropriate Standards Normally your Naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended to reduce this responsibility in any way. -
Page 3: Getting Started
Legal consumer protection varies from country to country. In most territories a dealer must be prepared to take back any Naim equipment he has sold you if he cannot make it work to your satisfaction in your own home. A problem may be due to a fault in any part of the system or its installation so it is essential to make full use of your local dealer’s... - Page 4 If there is a known problem in your locality it is advisable to arrange for a home demonstration before purchase to find out if Naim equipment is likely to be affected. Susceptibility to radio frequency interference is related to the wide internal bandwidth necessary for high sound quality.
-
Page 5: Mains Lead
4.3 fuse carrier Should the plug fuse carrier be damaged or lost, the correct replacement must be obtained from your dealer or from Naim direct. Do not use the plug until the fuse carrier is replaced. 4.4 plug fuses Replace only with ASTA or BS 1362 approved fuses. - Page 6 supercap power supply mains input Socket 1 Socket 2 Sockets 3, 4, 5 Socket 6 nac 52 only ch 2 Socket 7 nac 52 or snaxo only hi-cap power supply mains input Sockets 1, 2, 3 Socket 4 ch 2 flatcap 2 power supply power mains input...
- Page 7 nac 52 connection to supercap to nap 135, & 500 power amplifiers mains input to nap 140, 150, 180 & 250 power amplifiers or with extra hi-cap (or flatcap 2) for snaxo mains input to snaxo Interconnect Cables cable 4 to 4 pin DIN direction 5 to 5 pin DIN marker...
- Page 8 nac 52 connection to supercap with extra supercap for snaxo mains input mains input to snaxo...
- Page 9 nac 82 connection to one hi-cap or flatcap 2 link plug fitted link plug removed to napsc to nap 140, 150, 180 & 250 power amplifiers to nap 135 & 500 power amplifiers mains input nac 82 connection to two hi-caps or flatcaps 2 all link plugs removed to napsc to nap 135 &...
- Page 10 nac 82 connection to supercap all link plugs removed to napsc mains input to snaxo to nap 140, 150, 180 & to nap 135 & 500 250 power amplifiers power amplifiers with extra hi-cap or flatcap 2 for snaxo mains input to snaxo Interconnect Cables cable...
- Page 11 nac 82 connection to supercap with extra supercap for snaxo all link plugs removed to napsc mains input to snaxo to nap 140, 150, 180 & to nap 135 & 500 250 power amplifiers power amplifiers mains input to snaxo Interconnect Cables cable 4 to 4 pin DIN...
-
Page 12: Specifications
nac 112 connected to flatcap 2 link plug fitted for CD5, headline or stageline (additional) power mains input interconnects required with extra flatcap 2 for snaxo for CD5, headline or stageline (additional) power mains input to snaxo interconnects required Specifications supercap, hi-cap, flatcap 2 DC Outputs Mains Supply... - Page 13 (performance criterion B) IEC 801-3 3V/m 20dB (performance criterion A) IEC 801-4 1KV (AC lines) 0.5KV (signal lines) (performance criterion B) OWNPS issue 3 May 2001 • • Naim Audio Southampton Road Salisbury England SP1 2LN Tel: +44 (0)1722 332266 www.naim-audio.com...
Need help?
Do you have a question about the FLATCAP 2 - MANUEL 2 and is the answer not in the manual?
Questions and answers
What Naim cd reader is compatible with flatcap 2?
The Naim CD reader compatible with the FlatCap 2 is the CD5.
This answer is automatically generated