Linortek iTrixx-WFMN Quick Setup Instructions Manual

iTrixx-WFMN Wireless Hour Meter Quick
Setup Instruction
Thank you for purchasing the Linortek iTrixx-WFMN
Wireless Hour Meter. The iTrixx is an IoT controller and
runtime meter with digital inputs, analog inputs and
relay outputs capable of tracking runtime hours of up to
two different pieces of equipment. For complete setting
instructions, please refer to the
and Operation Manual.

Table of Contents

1. Packing List .................................................................................... 1
2. Safety Instructions ........................................................... 1
3. Get to Know iTrixx-WFMN Hardware .............................. 1
4. Activate the Meter .......................................................... 1
5. Make Connections ........................................................... 2
6. Connect to Your Network ................................................ 2
7. Find the IP Address .......................................................... 4
8. Program iTrixx from Telnet ............................................. 4
9. iTrixx Server Basic Configuration ..................................... 4
10. Using a Current Sensor to Activate the Meter ............... 5
11. Monitoring the Meter ................................................... 6
12. Data Integration ............................................................ 7
13. Product Manuals & Resources ...................................... 7
14. Technical Support .......................................................... 7
Board Reference Layout ...................................................... 7

1. Packing List

Please inspect the contents of your product kit. Each
SERVER is sent in its own box and includes:
☐ iTrixx-WFMN-ADi Server (01-910-00060)
☐ iTrixx-WFMN-Di Server (01-910-00064)
☐ 12 VDC power supply (01-850-00034)
☐ 2.2k Ohm resistor kit (01-880-00134)
☐ Current Sensor (01-390-00022)
☐ Wago Connectors (01-850-00029) (4)
☐ iTrixx-WFMN Quick Setting Instructions (this
document)

2. Safety Instructions

This section outlines critical safety guidelines that must
be followed to ensure proper operation and prevent
damage to the device:
-
Power Supply Requirements:
•
This device can be powered by 12-48VDC power
source. If your equipment cannot provide such
power source to power the device, use only the
power adapter provided by Linortek that comes
with your order. Other power supplies may
damage or destroy the device, affect its
behavior, or induce noise.
- Installation Environment:
iTrixx-WFMN Owners
•
This device is for indoor use only! NOT FOR
OUTDOOR USE!
•
Do NOT install the device in rooms with high
humidity.
•
Do NOT immerse the device in water and do
NOT spill or pour liquids of any kind onto or into
the device.
- Safety Precautions:
•
Do NOT install the device in surroundings at risk
for explosions.
•
Do NOT use the device if you smell gas or other
potentially explosive fumes.
•
Do NOT use the device during thunderstorms.
Lightning striking the power grid may cause
electric shocks.

3. Get to Know iTrixx-WFMN Hardware

There is 1 cable on the iTrixx-WFMN-Di, 3 cables on the
iTrixx-WFMNA-ADi. From the top to bottom, they are
described as cable 1, 2, 3. See the iTrixx-WFMN
Reference Layout at the end of this instruction to locate
the push buttons and wire chart mentioned in this
instruction.

4. Activate the Meter

The iTrixx-WFMN is designed to be integrated into
existing equipment to monitor run-time. Installing your
iTrixx will involve tapping circuits on the equipment you
intend to monitor.
The iTrixx Hour Meter has two separate hour counters
on the software. The hour counters may be activated in
several ways:
4.1 Power-based Activation
In the simplest setup the iTrixx may be activated
whenever power is applied to the unit. In this case, if
the iTrixx is on, it is counting. A voltage threshold is
provided so the iTrixx may stop counting as power is
lost to prevent memory corruption. In this way, you
only need to connect the iTrixx to the same power
source of the equipment you wish to collect running
data, no other wiring required.
4.2 Digital Input Activation
Use one of the two digital inputs to turn counting on
and off. The digital inputs can detect an external on/off
state of a sensor or a 5-24VDC signal from a PLC.
4.3 Analog Input Activation (iTrixx-WFMN-Adi only)
Activate the hour counter from data collected by an
analog sensor such as a current sensor.
Board