Fender CYBER-TWIN SE Manual page 15

R
EVERB TONE / SHAPE
REVERB TIME
REVERB DIFFUSION
TIMBRE
SPEAKER PHASE
COMPRESSION
NOISEGATE DEPTH
NOISEGATE THRESHOLD
EXPRESSION PEDAL ASSIGNMENT
CONT. CONTROLLER ASSIGNMENT
REVERB / FX BYPASS
w w w w w w . . f f e e n n d d e
Adjusts the Reverb high–frequency tone. Or, if Gated Reverb is active, this parameter
adjusts Reverb Shape with which radical decay characteristics can be achieved such as
rectangular, linear and reverse tails.
Values: 1.0 (minimum)
Adjusts the Reverb sustain time.
Values: 1.0 (shortest)
Adjusts the Reverb decay from a sparse/irregular sound to a dense/smooth sound.
Values: 1.0 (sparse)
Shifts the equalization of the amplifier providing instant tone shaping to accommodate
playing styles or to compensate for different room acoustics.
Values: None
Scoop Super Bright
Selects the phase polarity (push/pull or pull/push) for each speaker. Fender amps with
Reverb have traditionally had speakers operating in reverse polarity due to the extra tube
gain stage necessary for Reverb.
placement in the studio.
Values: Both Standard
Use to compress (moderate) the range of volume output due to extremes between soft
and loud guitar playing intensities.
fundamental component of many amplifiers.
Values: Off Low
Use to set the frequency cut–off boundary for the noisegate when it is activated.
Values: 1.0 10.0
Use to set the signal level sensitivity for activating the noisegate. Affected by TRIM
setting.
Values: Low Medium
Assigns a parameter to be controlled by an expression pedal (optional). Parameters in
[brackets] appear only when a particular effect or Reverb is active. For a list of effects
parameters, see page 16, for Reverb parameters, see above.
Values: Volume
[FX Val 1] [FX Val 2]
[Dwell] Reverb Tone [Shape]
Assigns a parameter to be controlled by a MIDI continuous controller pedal (optional).
Parameters in [brackets] appear only when a particular effect or Reverb is active. For
effects types/parameters, see page16, for Reverb types/parameters, see above.
Values: Volume
[FX Val 1] [FX Val 2]
[Dwell] Reverb Tone [Shape]
Use to bypass the in or out signals for Reverb "tail" and/or effects. Or, when Vibratone
is the active effect, the Rotor Speed Fast/Slow parameter is available for switching
between two (adjustable) rotor speeds (see Vibratone, page 20).
Values: FX In
Out FX Out & Reverb In
e r r . . c c o o m m
10.0 (maximum)
10.0 (longest)
10.0 (dense)
Full Body Razor Edge
Squawk Acoustic Scoop
Useful when experimenting with stereo mike
Both Reverse
Compression also provides sustain and is a
Medium High Even Higher
High
Gain Treble Middle
[FX Val 3] [FX Val 4]
Reverb Time
Gain Treble Middle
[FX Val 3] [FX Val 4]
Reverb Time
Reverb In FX Out Reverb Out
FX & Reverb Out
w w w w w w . . m m r r g g e
Amp Edit Mode
Bright & Light Bass Booster
Left Reverse Right Reverse
Bass Presence Reverb
Master Volume
Reverb Diffusion
Bass Presence Reverb
Master Volume
Reverb Diffusion
FX & Reverb In
[Rotor Speed Fast/Slow]
e a a r r h h e e a a d
15
Drop
[FX Level]
Reverb In Level
[FX Level]
Reverb In Level
FX In & Reverb
d . . n n e e t t