Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Standby MCS-NX-32
Summary of Contents for Standby MCS-NX-32
- Page 1 MCS-NX-32 INSTALLATION GUIDE 10R-0213006 C-10749-A_MDX00069_HW03/25...
-
Page 2: Table Of Contents
MCS-NX-32 Installation Guide CONTENTS Pre-Installation & Required Tools ......................... 4 1.1) Crimping Tool ........................4 1.2) Replacement Pins ........................4 1.3) Connector Receptacles ......................4 1.4) MHE Replacement Connector Pack ..................5 2.1) Installation Requirements ...................... 6 3.1) Mounting ..........................7 4.1) - Page 3 MCS-NX-32 Installation Guide Table of Figures Figure 1 Dimensions and Mounting holes ..................... 7 Figure 2 Connector Layout ..........................8...
-
Page 4: Pre-Installation & Required Tools
MCS-NX-32 Installation Guide Pre-Installation & Required Tools Crimping Tool 1.1) Universal Molex Crimp Tool. Molex part number: 0638111000 • http://www.digikey.co.uk/ Part Number: WM9999-ND • http://www.mouser.co.uk Part Number: 538-63811-1000 • http://uk.rs-online.com/ Part Number: 710-6499 • http://www.ttieurope.com Part Number: 63811-1000 Anderson PowerPole Crimp Tool Anderson part number: 1309G4 •... -
Page 5: Mhe Replacement Connector Pack
• http://www.digikey.co.uk/ Part Number: WM10386-ND • http://www.mouser.co.uk Part Number: 538-171692-0104 Anderson PP75 5916G7-BK • http://www.digikey.co.uk/ Part Number: 2243-5916G7-BK-ND • http://www.mouser.co.uk Part Number: 879-5916G7-BK MHE Replacement Connector Pack 1.4) 2021040 MCS-NX-32 Pins and Connector Pack 2021040-S MCS-NX-32S Pins and Connector Pack... -
Page 6: Installation Requirements
Each power connector (Anderson PowerPole) must be fused with a fuse rated to 70A or less. 2.1.2) DO NOT obstruct fan vents along the side of the MCS-NX-32. Do not install any equipment on top or underneath the MCS-NX-32. 2.1.3) The MCS system uses 6 pin RJ11 connectors and the MCS-NX uses RJ45 8 pin connectors, they utilize the same handsets and external CAN devices. -
Page 7: Mounting
MCS-NX-32 Installation Guide Mounting 3.1) Figure 1 Dimensions and Mounting holes 4 x M4 holes are supplied for mounting the unit to a base panel. -
Page 8: Wiring
MCS-NX-32 Installation Guide Wiring 4.1) Figure 2 Connector Layout 4.1.1) Name Function Connection for Active Antenna for GPS function (designated by G1) 4.1.2) SPKR -Siren Output (S1 and S2) Name Function Speaker 2 Channel A Negative Output Speaker 2 Channel B Negative Output... -
Page 9: 6) Connector B- Low Power Outputs
MCS-NX-32 Installation Guide 4.1.6) Connector B- Low Power Outputs Name Function Low Power Output 5 User Defined Low Power Outputs (Positive or Negative 2.4) *Note2 Low Power Output 6 User Defined Low Power Outputs (Positive or Negative 2.4A) *Note2 Low Power Output 7 User Defined Low Power Outputs (Positive or Negative 2.4A) -
Page 10: 10) Connector E - Input Connector
MCS-NX-32 Installation Guide 4.1.10) Connector E - Input Connector Name Function User defined input (pull-down through 11kΩ) Positive Input 10 No Connection User defined input (pull-down through 11kΩ) Positive Input 8 User defined input (pull-down through 11kΩ) Positive Input 9 No Connection User defined input (pull-down through 11kΩ) -
Page 11: 15) Connector J - High Power Outputs
MCS-NX-32 Installation Guide 4.1.15) Connector J - High Power Outputs Function Function High Power Output 25 User Defined High Power Output (Positive Switched 20A) High Power Output 26 User Defined High Power Output (Positive Switched 20A) High Power Output 27... -
Page 12: 21) Can2 Connector
MCS-NX-32 Installation Guide 4.1.21) CAN2 Connector Name Function CAN2H CAN2 High (CAN-FD) No Connection CAN2L CAN2 Low (CAN-FD) 4.1.22) RST - Reset Button Button for resetting of the unit. 4.1.23) SEL - Select Button Button for selecting what information is displayed by the LEDs on the unit. Also used to force the unit into bootloader mode. -
Page 13: Version History
MCS-NX-32 Installation Guide Version History 5.1) Version Changes Responsible Date Person(s) Initial document release KJVR 2022/05/10 Added no connection to the CAN connectors KJVR 2022/05/12 Updated connector information KJVR 2025/01/10 Updated the Dimensional drawing and render KJVR 2025/01/23...
Need help?
Do you have a question about the MCS-NX-32 and is the answer not in the manual?
Questions and answers