Related Manuals for caron RCDR316
Summary of Contents for caron RCDR316
- Page 1 6″ BUILT-IN TEMPERATURE RECORDER - RCDR316 6″ BUILT-IN TEMPERATURE/HUMIDITY RECORDER - RCDR317 For Technical Support contact service@caronproducts.com For Replacement Parts contact parts@caronproducts.com...
-
Page 2: Revision Log
Revision Log Revisions Description Letter Date 03-08-2016 Initial release. INST-RCDRRI 316-317 6 inch Cobex Rev A 03/08/2016 Page 2... - Page 3 Pen Cartridge, Blue (PN PEN-104) Chart Paper 6″, 7 Day 0C to 60C (PN PPR-104) or Chart Paper 6″, 7 Day 0C to 100C (PN PPR-105) STEP 1 – Unpack Contents of RCDR316 or RCDR317 INST-RCDRRI 316-317 6 inch Cobex Rev A 03/08/2016...
- Page 4 Parts included in RCDR316 or RCDR317 are (1) chart recorder with recorder panel with sensor and transformer wires, (2) 6-32 X 1/2″ black Phillips screws labeled “A”, (1) 6-32 X 3/8″ silver Phillips screw labeled “B”, (1) 6-32 X 3/8″ silver Phillips self- tapping screw labeled “C”, (1) wire sleeve clip, (1) transformer with harness and (1) chart recorder...
- Page 5 1. Turn off chamber and unplug power cord. Disconnect electrical power before removing top access panel. 2. Remove (3) screws in top access panel along front of chamber using Phillips screwdriver bit as shown below. Note: Retain screws. 3. Remove top access panel by sliding towards front of chamber until (3) tabs on each side are released as shown below.
- Page 6 1. Open chamber door, align recorder bracket and door cover edges and mark both mounting holes as shown below. Note: Let recorder panel with attached wire sleeve hang off to side of chamber while installing recorder. 2. Use #33 bit and #6-32 tap to drill and tap (2) mounting holes as shown below. Drilling Mounting Holes Tapping Mounting Holes STEP 4 –...
- Page 7 Use #33 bit and #6-32 tap to drill and tap mounting hole for wire sleeve clip located approximately 4″ below screw on right side of chamber and 1″ to right of door as shown below. Note: Accessory panels may appear different depending on option.
- Page 8 Tapping Mounting Hole STEP 5 – Attach Recorder Note: If chamber has solid door option remove tape from recorder, discard and skip #1 and #4. 1. Remove adhesive from tape on back of recorder. Note: Once adhesive has touched glass it cannot be moved. 2.
- Page 9 STEP 6 – Replace Accessory Panel with Recorder Panel 1. Remove (2) screws in right side front accessory panel using Phillips screwdriver bit as shown below. Note: Retain screws. Accessory panels may appear different depending on option. Right Side Front Accessory Panel Screws 2.
- Page 10 5. Insert recorder wire sleeve into wire sleeve clip and mount to side of chamber with silver “B” screw included as shown below. Wire Sleeve Clip STEP 7 – Preparation to Install Recorder Sensor inside Chamber 1. Remove shelves near sensor access plate inside chamber and remove sensor access plate by sliding latches downward as shown below.
-
Page 11: Step 8 - Transformer Connections
STEP 8 – Transformer Connections Note: All steps listed in this section refer to parts located in service compartment which may appear different depending on chamber options. 1. Connect recorder red wire to transformer on bottom left and black wire to transformer on bottom right as shown below. - Page 12 STEP 9 –Connect Recorder Power Harness Note: All steps listed in this section refer to parts located in service compartment which may appear different depending on chamber options. 1. Connect transformer power harness to (green/yellow and brown/blue) chamber power harness labeled “CHART RECORDER” as shown below. Chamber Recorder Power Harness in Service Compartment Transformer Power Harness Chamber Recorder Power Harness...
- Page 13 2. Loosen rear bulkhead fitting with channel locks as shown below. Rear Bulkhead in Service Compartment Rear Bulkhead Fitting 3. Remove insulation as shown below. Note: Retain insulation. Rear Bulkhead in Service Compartment Insulation INST-RCDRRI 316-317 6 inch Cobex Rev A 03/08/2016 Page 13...
- Page 14 4. Insert recorder sensor into rear bulkhead, feed recorder sensor from rear bulkhead behind rear wall plenum to sensor access plate and insert into clip as shown below. Note: Recorder sensor, wire and clip location may appear different depending on recorder option as shown below. Rear Bulkhead in Service Compartment Recorder Sensor Rear Wall Plenum...
- Page 15 5. Reinstall sensor access plate by sliding latches upward as shown below. Sensor Access Plate Sensor Access Plate Latches 6. Reinstall shelves. 7. Remove slack from recorder sensor wire, coil and secure with wire clip as shown below. Wire Clip in Service Compartment Wire Clip INST-RCDRRI 316-317 6 inch Cobex Rev A 03/08/2016...
- Page 16 Wrap insulation around wires in rear bulkhead as shown below. Rear Bulkhead in Service Compartment Insulation 9. Tighten rear bulkhead fitting in service compartment with channel locks as shown below. Rear Bulkhead in Service Compartment Rear Bulkhead Fitting INST-RCDRRI 316-317 6 inch Cobex Rev A 03/08/2016 Page 16...
- Page 17 10. Seal recorder sensor and wires in rear bulkhead with retained permagum as shown below. Rear Bulkhead in Service Compartment Recorder Sensor and Wires Sealed with Permagum STEP 11 – Install Top Access Panel 1. Install top access panel by sliding towards rear of chamber until (3) tabs on each side are engaged as shown below.
- Page 18 2. Secure top access panel along front of chamber with retained (3) screws using Phillips screwdriver bit as shown below. Screw Locations STEP 12 – Prepare Recorder 1. Plug in power cord and turn on chamber. 2. Open recorder door by pulling on magnetic door latch as shown below. Magnetic Door Latch 3.
- Page 19 4. Remove pen cartridge cap(s) as shown below. Note: Retain pen cartridge cap(s) to be used when chart recorder is not in service to extend pen cartridge life. Do not bend pen(s) when handling. Pen Cartridge Caps 5. Remove chart recorder paper hub by turning hub counterclockwise as shown below.
- Page 20 8. Press and hold “change chart” button (#3) for approximately one second until chart recorder pen begins to move back onto chart recorder paper and release button. Note: Verify chart recorder pen(s) are marking on chart recorder paper. If necessary, adjust chart recorder pen arm(s) by bending slightly. 9.
Need help?
Do you have a question about the RCDR316 and is the answer not in the manual?
Questions and answers