Download
Share
Print this page
  1. Manuals
  2. Brands
  3. caron Manuals
  4. Measuring Instruments
  5. RCDR318
  6. Manual

caron RCDR318 Manual

10″ built-in temperature/humidity recorder
Hide thumbs Also See for RCDR318:

Advertisement

Quick Links

Download this manual
10" BUILT-IN TEMPERATURE RECORDER – RCDR318
10" BUILT-IN TEMPERATURE/HUMIDITY RECORDER - RCDR319
For Technical Support contact
service@caronproducts.com
For Replacement Parts contact
parts@caronproducts.com
or visit
http://caronproducts.com/services
-parts/orders/ordering-parts.html

Advertisement

loading
Need help?

Need help?

Do you have a question about the RCDR318 and is the answer not in the manual?

Questions and answers

Related Manuals for caron RCDR318

Summary of Contents for caron RCDR318

  • Page 1 10″ BUILT-IN TEMPERATURE RECORDER – RCDR318 10″ BUILT-IN TEMPERATURE/HUMIDITY RECORDER - RCDR319 For Technical Support contact service@caronproducts.com For Replacement Parts contact parts@caronproducts.com or visit http://caronproducts.com/services -parts/orders/ordering-parts.html...

  • Page 2: Revision Log

    Revision Log Revisions Description Letter Date 07-11-2017 Initial release. INST-RCDRBT 318-319 10 inch Cobex Rev A 07/11/2017 Page 2...
  • Page 3 Instructions for Installing 10″ Built-in Recorder with Temperature or Temperature/Humidity Option Parts Required: RCDR318 or RCDR319 Tools Required: Phillips Screwdriver Bit, Drill, #33 Drill Bit, #6-32 Tap, Ladder, Tape Measure, Sharpie Marker Consumable Item: Chart Paper 10″ for Cobex Thermal Pen (PN PPR-106) Consumable item included in 10″...
  • Page 4 STEP 1 – Unpack Contents of RCDR318 or RCDR319 Parts included in RCDR318 or RCDR319 are (1) chart recorder with recorder panel with sensor and transformer wires, (2) 6-32 X 1/2″ black Phillips screws labeled “A”, (2) 6-32 X 3/8″ silver Phillips self-tapping screws labeled “B”, (2) 6-32 X 3/8″...
  • Page 5 STEP 2 – Drill and Tap Door in Preparation for Mounting 1. Turn off chamber and unplug power cord. 2. Use #33 bit and #6-32 tap to drill and tap (2) mounting holes on top of chamber door as shown below. Drilling Mounting Holes Tapping Mounting Holes INST-RCDRBT 318-319 10 inch Cobex...
  • Page 6 STEP 3 – Install Wire Sleeve Clips 1. Use tape measure and #33 bit to drill mounting hole for wire sleeve clip on right side of chamber near door hinge located 4.25″ below top of chamber and to right of side seam as shown below.
  • Page 7 3. Use tape measure and #33 bit to drill mounting hole for wire sleeve clip on left rear side of chamber located 4.25″ below top of chamber and 3.25″ from left side of chamber as shown below. Drilling Mounting Hole 4.
  • Page 8 5. Use #6-32 tap on (4) mounting holes for wire sleeve clips as shown below. 6. Insert (4) wire sleeve clips into previously tapped mounting holes and fasten with (4) silver “C” screws included using Phillips screwdriver bit as shown below. Wire Sleeve Clip Screw Location STEP 4 –...
  • Page 9 STEP 5 – Replace Accessory Panel with Recorder Panel 1. Remove (2) screws in top rear accessory panel using Phillips screwdriver bit as shown below. Note: Retain screws. Accessory panels may appear different depending on option. Accessory Panel Screws 2. Remove and discard top rear accessory panel. 3.
  • Page 10 5. Insert wire sleeve into (4) wire sleeve clips and squeeze closed as shown below. Open Wire Sleeve Clip Closed Wire Sleeve Clip Rear Wire Sleeve Clips Right Side Wire Sleeve Clips STEP 6 – Preparation to Install Recorder Sensor inside Chamber 1.
  • Page 11 2. Remove sensor access plate by sliding latches towards center of sensor access plate by sliding latches downward as shown below. Sensor Access Plate Latches Sensor Access Plate 3. Feed sensor access plate through opening in right side duct sheet as shown below. Right Side Duct Sheet Opening 4.
  • Page 12 6. Remove (2) screws securing left interior wall using Phillips screwdriver bit as shown below. Note: Retain screws. Left Interior Wall Screws 7. Tilt top of left interior wall down towards bottom of chamber, remove and set aside. 8. Release (2) latches on top right interior wall as shown below. Right Interior Wall Latches 9.
  • Page 13 10. Release (2) latches on left side interior false wall and tilt to rest on right side of chamber as shown below. Left Side Interior False Wall Latches Left Side Interior False Wall STEP 7 – Remove Side Access Panel 1.
  • Page 14 2. Pull side access panel outward until (2) access panel tabs on bottom are released as shown below. Access Panel Tabs STEP 8 – Transformer Connections Note: All steps listed in this section refer to parts located in service compartment which may appear different depending on chamber options.
  • Page 15 2. Mount transformer with (2) silver “B” screws included using Phillips screwdriver bit as shown below. Mounting Locations for Transformer Transformer Location Area in Service Compartment Mounting Transformer STEP 9 –Connect Recorder Power Harness Note: All steps listed in this section refer to parts located in service compartment which may appear different depending on chamber options.
  • Page 16 2. Secure excess wires in wire harness clip as shown below. Wire Harness Clip STEP 10 – Install Recorder Sensor Note: All steps listed in this section refer to parts located in service compartment which may appear different depending on chamber options. 1.
  • Page 17 2. Feed recorder sensor through (3) wire clips across top of service compartment as shown below. Note: Recorder sensor, wire and clip location may appear different depending on recorder option. 3. Insert recorder sensor into access port, feed recorder sensor through (3) wire clips across top of chamber as shown below.
  • Page 18 6. Reinstall false top and right interior wall by using right interior wall to support false top and secure (2) latches on right interior wall. 7. Reinstall sensor access plate by sliding latches outward. 8. Remove slack from recorder sensor wire, coil and secure with wire clip as shown below. Wire Clip 9.
  • Page 19 12. Align tabs on bottom left interior wall with slots on bottom left side interior wall and align to be flush with left side interior false wall as shown below. Left Interior Wall Tabs 13. Secure left interior wall with retained (2) screws using Phillips screwdriver bit. 14.
  • Page 20 3. Press and hold “change chart” button on chart recorder (#3) for approximately one second until chart recorder pen begins to move off chart recorder paper and release button as shown below. Change Chart Button 4. Remove pen cap as shown below. Note: Retain pen cap to be used when chart recorder is not in service to extend pen life.
  • Page 21 6. Insert chart recorder paper under chart recorder paper guides as shown below. Paper Guides Paper Guides 7. Secure chart recorder paper with chart recorder paper hub. 8. Press and hold “change chart” button (#3) for approximately one second until chart recorder pen begins to move back onto chart recorder paper and release button.

This manual is also suitable for:

Rcdr319