Installation - Pioneer Premier DEH-P700BT Installation Manual

Installation

English
DIN Front/Rear-mount
Note
This unit can be properly installed either from
• Check all connections and systems before final
"Front" (conventional DIN Front-mount) or
installation.
"Rear" (DIN Rear-mount installation, utilizing
• Do not use unauthorized parts. The use of
threaded screw holes at the sides of unit
unauthorized parts may cause malfunctions.
chassis). For details, refer to the following
• Consult with your dealer if installation requires
installation methods.
drilling of holes or other modifications of the
vehicle.
Removing or attaching
• Do not install this unit where:
— it may interfere with operation of the vehicle.
the trim ring
— it may cause injury to a passenger as a result
of a sudden stop.
1. Extend top and bottom of the trim
• The semiconductor laser will be damaged if it
ring outwards to remove the trim
overheats. Install this unit away from hot places
such as near the heater outlet. ring.
• Optimum performance is obtained when the unit is
• When reattaching the trim ring, push the trim
installed at an angle of less than 60°.
ring onto the unit until it clicks. (If the trim
ring is attached upside down, the trim ring will
not fit properly.)
• It becomes easy to remove the trim ring if the
60°
front panel is released.
• When installing, to
Trim ring
ensure proper heat dispersal when using this unit,
make sure you leave ample space behind the rear
panel and wrap any loose cables so they are not
blocking the vents.
Dashboard
Leave ample space
10cm (3-7/8 in.)
10cm (3-7/8 in.)
• The cords must not cover up the area shown in
the figure below. This is necessary to allow the
amplifires to radiate freely.
Do not cover this area.
Installation English
DIN Front-mount DIN Rear-mount
Installation with the rubber bush 1. Determine the appropriate position
where the holes on the bracket and
1. Secure the mounting sleeve by
using a screwdriver to bend the the side of the unit match.
metal tabs (90°) into place.
Mounting sleeve
Dashboard
1 1 1 82 182
Rubber bush
53 53
2. Tighten two screws on each side.
Screw
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
2. Install the unit as illustrated.
Removing the Unit
1. Insert the supplied extraction keys
into both sides of the unit until
they click into place.
Dashboard or Console
Factory radio mounting bracket
2. Pull the unit out of the dashboard.
Installation
Fastening the front panel Installing the microphone
If you do not plan to detach the front panel,
Installation notes
the front panel can be fastened with supplied
Install the microphone in a position and
screws and holders.
orientation that will enable it to pick up the
1. Attach the holders to both sides of
voice of the person operating the system.
the front panel.
CAUTION
• It is extremely dangerous to allow the microphone
lead to become wound around the steering
column or gearstick. Be sure to install the unit in
such a way that it will not obstruct driving.
When installing the microphone
2. Replace the front panel to the unit.
on the sun visor
1. Install the microphone on the
Screw
microphone clip.
3. Flip the holders into upright
positions.
2. Install the microphone clip on the
sun visor.
• With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the
recognition rate for voice operations.)
4. Fix the front panel to the unit using
screws.
Screw
Clamps
Use clamps to secure
the lead where
necessary inside the
vehicle.
English Installation
When installing the microphone
on the steering column
1. Install the microphone on the
microphone clip.
Microphone
Fit the
microphone lead
into the groove.
Microphone clip
2. Install the microphone clip on the
steering column.
Double-sided tape
Microphone
Microphone clip
Install the microphone clip on the
rear side of the steering column.
Microphone clip
Clamps
Use clamps to secure
the lead where
necessary inside the
vehicle.
English
Adjusting the microphone
angle
The microphone angle can be adjusted by
moving forward or backward the microphone
clip angle.