Download Print this page

attica CHATT0682-GBC Installation Manual

16-23 toyota tacoma rogue series headlights

Advertisement

Quick Links

Rogue Series Headlights
Before installation -
Read and understand all instructions,
warnings, cautions, and notes contained in this installation
instruction guide. Consult your vehicle owner's manual for proper
disconnection of electrical and li ting of vehicle if required for
installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing
this install please take this product to a trained professional.
A ter reading this guide please contact us with any questions or
concerns before installing product.
Customer Service: (626) 369-2121
ATTICA4X4 is not responsible for any bodily injury or harm to you or
your vehicle as a result of an improper install.
tech@attica4x4.com
16-23
Toyota Tacoma
CHATT0682-GBC
Proper installation of this kit requires knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand
during the installation. Installation of this kit without proper
knowledge of the factory recommended procedures may a ect the
performance of these components and the safety of the vehicle.
Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure product is not damaged and all
installation hardware has been included. If parts are missing from kit, please be
prepared to provide the following information:
Name of purchase location
Bar Code on side of box
Date above Bar Code
Date insde box cover
(626) 369-2121

Advertisement

loading
Need help?

Need help?

Do you have a question about the CHATT0682-GBC and is the answer not in the manual?

Questions and answers

Summary of Contents for attica CHATT0682-GBC

  • Page 1 16-23 Toyota Tacoma Rogue Series Headlights CHATT0682-GBC Before installation - Proper installation of this kit requires knowledge of the factory Read and understand all instructions, recommended procedures for removal and installation of original warnings, cautions, and notes contained in this installation equipment components.
  • Page 2: Tools Required

    tools required • 10mm socket 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM...
  • Page 3 Begin by unpacking all items and inspecting them for damage or missing items. Any concerns, please contact the company you purchased the headlights from. Unplug the grille power from the connector, as shown in the top le t. Use a 10mm socket tool to locate and remove the grille screws, and then remove the grille as shown in the top right.
  • Page 4 Use a 10mm socket tool to remove the screws and pry out the inner cover clips from the inner fender to create enough space to access the bumper screws. Remove the six inner cover clips from the grille. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM...
  • Page 5 Use a 10mm socket tool to detach the factory headlight by removing its bolts. Disconnect the factory halogen turn signal bulb. (We will later connect it to our LED turn signal using the Attica adapter.) 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM...
  • Page 6 Connect the wires to the headlight accordingly. The red wire with the green connector goes to your INJ fuse, located in the fuse box under the hood. We recommend using a fuse tap (It’s not included). Please note that the INJ fuse is used to start your car. If in the future your car fails to start, it could be due to the INJ fuse.
  • Page 7 If in the future your car fails to start, it could be due to the INJ fuse. Use the Attica adapter to connect the original turn signal connector with our Attica Rogue Series Headlight. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM...
  • Page 8 Connect the DRL wire and the parking light wire accordingly as shown at the top. Once all the wires are connected accordingly, the next step is to start installing our Attica Rogue Series Headlight onto your vehicle, following the same steps as when removing the factory light.
  • Page 9 Remember to reattach the inner cover clips. Reattach the grille using the factory screws and a 10mm socket tool. Once finished your Attica Rogue Series Headlights will be completely installed and ready to take to the outdoors! 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM...
  • Page 10 if you have any questions, please email us at tech@attica4x4.com or call us at 626-369-2121 (626) 369-2121 tech@attica4x4.com...